dr hab. inż. Łukasz Jankowski 

Doktorat
20041029  Modelling and simulation of light propagation in nonaged and aged stepindex polymer optical fibres (UP)
 1062 
Habilitacja
20140306  Dynamic load identification for structural health monitoring 
Promotor prac doktorskich
1.  20151029  Suwała Grzegorz  Nieparametryczna metoda identyfikacji zmian masy i sztywności konstrukcji  670 
Ostatnie publikacje
1.  Zawidzki M., Jankowski Ł., Multiobjective optimization of modular structures: Weight versus geometric versatility in a TrussZ system, ComputerAided Civil and Infrastructure Engineering, ISSN: 10939687, DOI: 10.1111/mice.12478, Vol.34, No.11, pp.10261040, 2019 Streszczenie: This paper proposes an approach for multicriterial optimization of modular structures with respect to their structural and geometrical properties. The approach is tested using the quickly deployable and reconfigurable modular ramp system TrussZ intended for pedestrian traffic. The focus is on modular structures composed of a moderate number of relatively complex modules, which feature an irregular, noncuboidal geometry. Such modules can be assembled into a variety of geometrically different configurations which do not adhere to any predefined spatial grid; their global geometry can be treated as freeform and determined in situ during construction. The optimization variables represent locallevel geometrical and structural properties of a single module. The Pareto front is used to balance between two kinds of objectives. The geometrical objective quantifies the ability of the modules to generate geometrically versatile global structures that are wellsuited to comply with spatial constraints of real construction sites. The structural objective is formalized in analogy to the minimum weight problem with upper bound constraints imposed on the von Mises stress and the Euler buckling load ratio. A twolevel optimization scheme is employed with NSGAII at the top level and a simulated annealing with adaptive neighborhood at the lower level. Słowa kluczowe: modular structures, multicriterial optimization, shape optimization, sizing optimization, NSGAII, simulated annealing with adaptive neighborhood Afiliacje autorów:
 140p.  
2.  Faraj R., Jankowski Ł., Graczykowski C., HolnickiSzulc J., Can the inerter be a successful shockabsorber? The case of a ballscrew inerter with a variable thread lead, Journal of the Franklin Institute, ISSN: 00160032, DOI: 10.1016/j.jfranklin.2019.04.012, Vol.356, No.14, pp.78557872, 2019 Streszczenie: This paper investigates an application of a ballscrew inerter for mitigation of impact loadings. The problem of impact absorption is to provide a minimum reaction force that optimally decelerates and eventually stops an impacting object within the available absorber stroke. It significantly differs from vibration mitigation problems which are typical application of inerters. The paper demonstrates that the optimum absorption can be achieved by fully passive means. For known values of the object mass and inerter parameters, the obtained solution is independent of the impact velocity. The optimum passive absorption is achieved by employing a variable thread lead. As a result, two force components emerge, the typical inertancerelated force and a dampinglike term, and sum up to provide the optimum constant deceleration force. This result is relatively unique: conventional absorbers do not provide a constant force even with complex active control systems. Finally, an optimization problem is formulated to reduce the influence of process uncertainties (range of possible mass values, unknown friction). The results are verified and analyzed in a numerical example. Afiliacje autorów:
 100p.  
3.  Hou J.^{♦}, Wang P.^{♦}, Jing T.^{♦}, Jankowski Ł., Experimental Study for Damage Identification of Storage Tanks by Adding Virtual Masses, SENSORS, ISSN: 14248220, DOI: 10.3390/s19020220, Vol.19, No.2, pp.220117, 2019 Streszczenie: This research proposes a damage identification approach for storage tanks that is based on adding virtual masses. First, the frequency response function of a structure with additional virtual masses is deduced based on the Virtual Distortion Method (VDM). Subsequently, a Finite Element (FE) model of a storage tank is established to verify the proposed method; the relation between the added virtual masses and the sensitivity of the virtual structure is analyzed to determine the optimal mass and the corresponding frequency with the highest sensitivity with respect to potential damages. Thereupon, the damage can be localized and quantified by comparing the damage factors of substructures. Finally, an experimental study is conducted on a storage tank. The results confirm that the proposed method is feasible and practical, and that it can be applied for damage identification of storage tanks. Słowa kluczowe: damage identification, storage tanks, sensitivity analysis, frequency Afiliacje autorów:
 100p.  
4.  Hou J.^{♦}, Li Z.^{♦}, Zhang Q., Zhou R.^{♦}, Jankowski Ł., Optimal Placement of Virtual Masses for Structural Damage Identification, SENSORS, ISSN: 14248220, DOI: 10.3390/s19020340, Vol.19, No.2, pp.340118, 2019 Streszczenie: Adding virtual masses to a structure is an efficient way to generate a large number of natural frequencies for damage identification. The influence of a virtual mass can be expressed by Virtual Distortion Method (VDM) using the response measured by a sensor at the involved point. The proper placement of the virtual masses can improve the accuracy of damage identification, therefore the problem of their optimal placement is studied in this paper. Firstly, the damage sensitivity matrix of the structure with added virtual masses is built. The Volumetric Maximum Criterion of the sensitivity matrix is established to ensure the mutual independence of measurement points for the optimization of mass placement. Secondly, a method of sensitivity analysis and error analysis is proposed to determine the values of the virtual masses, and then an improved version of the Particle Swarm Optimization (PSO) algorithm is proposed for placement optimization of the virtual masses. Finally, the optimized placement is used to identify the damage of structures. The effectiveness of the proposed method is verified by a numerical simulation of a simply supported beam structure and a truss structure. Słowa kluczowe: damage identification, sensor optimization, Virtual Distortion Method (VDM), Particle Swarm Optimization (PSO) algorithm, sensitivity Afiliacje autorów:
 100p.  
5.  Popławski B., Mikułowski G., Pisarski D., Wiszowaty R., Jankowski Ł., Optimum actuator placement for damping of vibrations using the PrestressAccumulation Release control approach
, SMART STRUCTURES AND SYSTEMS, ISSN: 17381584, DOI: 10.12989/sss.2019.24.1.027, Vol.24, No.1, pp.2735, 2019 Streszczenie: This paper proposes a quantitative criterion for optimization of actuator placement for the Prestress–Accumulation Release (PAR) strategy of mitigation of vibrations. The PAR strategy is a recently developed semiactive control approach that relies on controlled redistribution of vibration energy into highorder modes, which are highfrequency and thus effectively dissipated by means of the natural mechanisms of material damping. The energy transfer is achieved by a controlled temporary removal of selected structural constraints. This paper considers a shorttime decoupling of rotational degrees of freedom in a frame node so that the bending moments temporarily cease to be transferred between the involved beams. We propose and test a quantitative criterion for placement of such actuators. The criterion is based on local modal strain energy that can be released into highorder modes. The numerical time complexity is linear with respect to the number of actuators and potential placements, which facilitates quick analysis in case of large structures. Słowa kluczowe: semiactive control, damping of vibrations, actuator placement, smart structures, prestressaccumulation release (PAR) Afiliacje autorów:
 70p.  
6.  Hou J.^{♦}, Wang S.^{♦}, Zhang Q.^{♦}, Jankowski Ł., An Improved Objective Function for ModalBased Damage Identification Using Substructural Virtual Distortion Method, Applied Sciences, ISSN: 20763417, DOI: 10.3390/app9050971, Vol.9, No.5, pp.117, 2019 Streszczenie: Damage identification based on modal parameters is an important approach in structural health monitoring (SHM). Generally, traditional objective functions used for damage identification minimize the mismatch between measured modal parameters and the parameters obtained from the finite element (FE) model. However, during the optimization process, the repetitive calculation of structural modes is usually timeconsuming and inefficient, especially for largescale structures. In this paper, an improved objective function is proposed based on certain characteristics of the peaks of the frequency response function (FRF). Traditional objective functions contain terms that quantify modal shapes and/or natural frequencies. Here, it is proposed to replace them by the FRF of the FE model, which allows the repeated full modal analysis to be avoided and thus increases the computational efficiency. Moreover, the efficiency is further enhanced by employing the substructural virtual distortion method (SVDM), which allows the frequency response of the FE model of the damaged structure to be quickly computed without the costly reanalysis of the entire damaged structure. Finally, the effectiveness of the proposed method is verified using an eightstory frame structure model under several damage cases. The damage location and extent of each substructure can be identified accurately with 5% white Gaussian noise, and the optimization efficiency is greatly improved compared with the method using a traditional objective function. Słowa kluczowe: structural health monitoring (SHM), damage identification, substructure, virtual distortion method (VDM), frequency response Afiliacje autorów:
 70p.  
7.  Popławski B., Mikułowski G., Mróz A., Jankowski Ł., Decentralized semiactive damping of free structural vibrations by means of structural nodes with an on/off ability to transmit moments, MECHANICAL SYSTEMS AND SIGNAL PROCESSING, ISSN: 08883270, DOI: 10.1016/j.ymssp.2017.08.012, Vol.100, pp.926939, 2018 Streszczenie: This paper proposes, tests numerically and verifies experimentally a decentralized control algorithm with local feedback for semiactive mitigation of free vibrations in frame structures. The algorithm aims at transferring the vibration energy of loworder, lightlydamped structural modes into highfrequency modes of vibration, where it is quickly damped by natural mechanisms of material damping. Such an approach to mitigation of vibrations, known as the prestressaccumulation release (PAR) strategy, has been earlier applied only in global control schemes to the fundamental vibration mode of a cantilever beam. In contrast, the decentralization and local feedback allows the approach proposed here to be applied to more complex frame structures and vibration patterns, where the global control ceases to be intuitively obvious. The actuators (truss–frame nodes with controllable ability to transmit moments) are essentially unblockable hinges that become unblocked only for very short time periods in order to trigger local modal transfer of energy. The paper proposes a computationally simple model of the controllable nodes, specifies the control performance measure, yields basic characteristics of the optimum control, proposes the control algorithm and then tests it in numerical and experimental examples. Słowa kluczowe: Damping of vibrations, Smart structures, Semiactive control, Decentralized control, Trussframe nodes Afiliacje autorów:
 45p.  
8.  Zawidzki M., Jankowski Ł., Optimization of modular TrussZ by minimummass design under equivalent stress constraint, SMART STRUCTURES AND SYSTEMS, ISSN: 17381584, DOI: 10.12989/sss.2018.21.6.715, Vol.21, No.6, pp.715725, 2018 Streszczenie: TrussZ (TZ) is an Extremely Modular System (EMS). Such systems allow for creation of structurally sound freeform structures, are comprised of as few types of modules as possible, and are not constrained by a regular tessellation of space. Their objective is to create spatial structures in given environments connecting given terminals without selfintersections and obstacleintersections. TZ is a skeletal modular system for creating freeform pedestrian ramps and ramp networks. The previous research on TZ focused on global discrete geometric optimization of the spatial configuration of modules. This paper reports on the first attempts at structural optimization of the module for a singlebranch TZ. The internal topology and the sizing of module beams are subject to optimization. An important challenge is that the module is to be universal: it must be designed for the worst case scenario, as defined by the module position within a TZ branch and the geometric configuration of the branch itself. There are four variations of each module, and the number of unique TZ configurations grows exponentially with the branch length. The aim is to obtain minimummass modules with the von Mises equivalent stress constrained under certain design load. The resulting modules are further evaluated also in terms of the typical structural criterion of compliance. Słowa kluczowe: Extremely Modular System, TrussZ, structural optimization, modular structures, minimum mass design, frame structures Afiliacje autorów:
 30p.  
9.  Hou J.^{♦}, An Y.^{♦}, Wang S.^{♦}, Wang Z.^{♦}, Jankowski Ł., Ou J.^{♦}, Structural Damage Localization and Quantification Based on Additional Virtual Masses and Bayesian Theory, JOURNAL OF ENGINEERING MECHANICSASCE, ISSN: 07339399, DOI: 10.1061/(ASCE)EM.19437889.0001523, Vol.144, No.10, pp.0401809719, 2018 Streszczenie: In vibrationbased damage identification, a common problem is that modal information is not enough and insensitive to local damage. To solve this problem, an effective method is to increase the amount of modal information and enhance the sensitivity of the experimental data to the local damage. In this paper, a damage identification method based on additional virtual masses and Bayesian theory is proposed. First, the virtual structure with optimal additional mass and high sensitivity to local damage is determined through sensitivity analysis, and then a large number of virtual structures can be obtained by adding virtual masses; thus, a lot of modal and statistical information of virtual structures can be obtained. Second, the Bayesian theory is used to obtain the posterior probability distribution of the damage factor when structural a priori information is considered. Third, by finding the extreme value of the probability density function, the damage factor is derived based on the a priori information and the statistical information of virtual structures. Finally, the effectiveness of the proposed method is verified by numerical simulations and experiments of a 3story frame structure. Experimental and numerical results show that the proposed method can be used to identify the damage severity of each substructure and thus damaged substructures can be localized and quantified; the error in damage factor is basically within 5%, which shows the accuracy of the proposed method. The proposed method can not only provide the structural damage localization and quantification result (i.e., the damage factor), but also the probability distribution of the damage factor; moreover, it has high sensitivity to damage and high accuracy and efficiency. Słowa kluczowe: Structural health monitoring, Damage identification, Bayesian theory, Virtual distortion method (VDM), Virtual mass Afiliacje autorów:
 30p.  
10.  Hou J.^{♦}, Jing T.^{♦}, Wang P.^{♦}, Zhang Q.^{♦}, Jankowski Ł., Damage identification method for storage tanks based on additional virtual masses, JOURNAL OF VIBRATION AND SHOCK, ISSN: 10003835, DOI: 10.13465/j.cnki.jvs.2018.13.002, Vol.37, No.13, pp.713, 2018 Streszczenie: A damage identification method based on additional virtual masses was proposed aiming at storage tanks’ features of spacesymmetry, dense lowerorder modes and being insensitive to local damages. Firstly, magnitudes of additional masses were determined through sensitivity analysis of storage tanks’ structural modes. Then based on the virtual deflection method (VDM), the tanks’ frequency responses after attaching additional virtual masses were constructed and their natural frequencies were identified with the original structures’ excitation time histories and the original structures’ corresponding positions’ acceleration response time histories. Furthermore, using the tanks’ features of spacesymmetry, their damage positions were preliminarily determined according to the distribution law of their natural frequencies after attaching virtual masses. The sensitivity analysis of the tanks’ finite element model was used to solve iteratively damages’ level. Finally, the tanks’ finite element models were used to perform numerical simulations and correctly predict their damage locations and levels. The effectiveness of this proposed method was verified. Słowa kluczowe: storage tanks, damage identification, sensitivity analysis, frequency Afiliacje autorów:
 
11.  Suwała G., Jankowski Ł., Nonparametric identification of structural modifications in Laplace domain, MECHANICAL SYSTEMS AND SIGNAL PROCESSING, ISSN: 08883270, DOI: 10.1016/j.ymssp.2016.09.018, Vol.18, pp.867878, 2017 Streszczenie: This paper proposes and experimentally verifies a Laplacedomain method for identification of structural modifications, which (1) unlike timedomain formulations, allows the identification to be focused on these parts of the frequency spectrum that have a high signaltonoise ratio, and (2) unlike frequencydomain formulations, decreases the influence of numerical artifacts related to the particular choice of the FFT exponential window decay. In comparison to the timedomain approach proposed earlier, advantages of the proposed method are smaller computational cost and higher accuracy, which leads to reliable performance in more difficult identification cases. Analytical formulas for the first and secondorder sensitivity analysis are derived. The approach is based on a reduced nonparametric model, which has the form of a set of selected structural impulse responses. Such a model can be collected purely experimentally, which obviates the need for design and laborious updating of a parametric model, such as a finite element model. The approach is verified experimentally using a 26node lab 3D truss structure and 30 identification cases of a single mass modification or two concurrent mass modifications. Słowa kluczowe: Structural health monitoring (SHM), Nonparametric model, Inverse problem, Virtual distortion method (VDM), Structural reanalysis, Sensitivity analysis, Laplace domain Afiliacje autorów:
 45p.  
12.  Michajłow M., Jankowski Ł., Szolc T., Konowrocki R., Semiactive reduction of vibrations in the mechanical system driven by an electric motor, OPTIMAL CONTROL APPLICATIONS & METHODS, ISSN: 01432087, DOI: 10.1002/oca.2297, Vol.38, No.6, pp.922933, 2017 Streszczenie: In this paper, a semiactive damping approach is used for reduction of vibrations in a laboratory drivetrain system. The considered drivetrain system is powered by an electric, asynchronous motor at the one side and loaded with a harmonically varying torque on the other side. Here, an influence of electromechanical interaction, i.e., an electromechanical coupling, between the electric motor and the mechanical system has been taken into consideration. The harmonic load signal induces torsional vibrations in the system, which in the steadystate phase of motion become periodic. The aim of the work is to determine the optimal control function for a semiactive damping element, leading to vibration reduction and considering only the steadystate phase of system motion. The optimal control is derived by using a semianalytical approach based on the optimal control theory aided with supplementary numerical computations. The proposed methodology is fully general, and it can be directly applied to any type of a periodically oscillating system. Słowa kluczowe: electric motor, electromechanical coupling, optimal control, periodic torsional vibrations, semiactive damping Afiliacje autorów:
 30p.  
13.  Zhang Q., Jankowski Ł., Damage identification using structural modes based on substructure virtual distortion method, ADVANCES IN STRUCTURAL ENGINEERING, ISSN: 13694332, DOI: 10.1177/1369433216660018, Vol.20, No.2, pp.257271, 2017 Streszczenie: A damage identification approach is presented using substructure virtual distortion method which takes the advantage of the fast structural reanalysis technique of virtual distortion method. The formulas of substructure virtual distortion method are deduced in frequency domain, and then the frequency response function of the damaged structure is constructed quickly via the superposition of the frequency response function of the intact structure and the frequency responses caused by the damagecoupling virtual distortions of the substructures. The structural damage extents are identified using the measured modal parameters. Two steps are adopted to increase the efficiency of optimization: the modals of finite element model are estimated quickly from the fast constructed frequency response function during the optimization and the primary distortions of the substructures are extracted by contribution analysis to further reduce the computational work. A sixstory frame numerical model and an experiment of a cantilever beam are carried out, respectively, to verify the efficiency and accuracy of the proposed method. Słowa kluczowe: damage identification, frequency domain, structural health monitoring, substructure, virtual distortion method Afiliacje autorów:
 20p.  
14.  HolnickiSzulc J., Ichchou M.^{♦}, Duan Z.^{♦}, Jankowski Ł., Adaptive Impact Absorption, MATHEMATICAL PROBLEMS IN ENGINEERING, ISSN: 1024123X, DOI: 10.1155/2016/4871549, Vol.2016, pp.487154912, 2016 Streszczenie: The surging quest for safety is a clearly visible trend in modern societies. One of the related areas of research is the design of systems protecting against heavy dynamic loads such as low and medium velocity trafficrelated impacts and environmental loadings. Commonly applied passive systems are typically designed to withstand a specified, welldefined heavy load scenario, which limits their performance over any wider range of loads, including the less heavy loads that are encountered in the lifetime of a typical structure much more often than the maximum limiting loads. Afiliacje autorów:
 20p.  
15.  Michajłow M., Szolc T., Jankowski Ł., Konowrocki R., SemiActive Reduction of Vibrations of Periodically Oscillating System, Solid State Phenomena, ISSN: 16629779, DOI: 10.4028/www.scientific.net/SSP.248.111, Vol.248, pp.111118, 2016 Streszczenie: Periodical vibrations are common phenomenon affecting a wide range of mechanical systems. Most frequently it affects machines designed to work in a steadystate conditions like: turbine, pump, rail vehicle, etc. In those kinds of machines it is always possible to decompose the system motion to basic averagespeed constant component and oscillatory component. Usually the second term is treated as undesirable and various techniques are applied in order to minimize it as far as it is possible. These techniques refers to both the hardware selection – meaning the type of damping system (active, semiactive, passive) and the control method selection – meaning the damping system control method. Concerning the control methods, there are many algorithms available in literature devoted to transient systems. One of typical application is to use them in systems experiencing sudden, external force excitation. After destabilization of the system, caused by excitation, the role of the control algorithm is to restore the system stable position and additionally to reach the extreme of some additional criterion. Typical criterions are minimization of the time, of restoring the stable position, minimizing the consumed control energy, etc. On the other hand, considering the steadystate systems, especially based on semiactive damping elements, there are not so many control methods available.This paper focuses on developing the proper methodology for deriving the optimal control strategy of semiactive damping element, to be used in periodically vibrating mechanical system. The control strategy is developed on the basis of the Optimal Control Theory. Numerical computations are involved in order to solve the optimal control problem for the considered test system. Problem solution reveals the periodical nature of optimal control function. Słowa kluczowe: Optimal Control Theory, Periodical Vibrations, Vibration Reduction Afiliacje autorów:
 
16.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Frequencydomain substructure isolation for local damage, ADVANCES IN STRUCTURAL ENGINEERING, ISSN: 13694332, DOI: 10.1260/13694332.18.1.137, Vol.18, pp.137154, 2015 Streszczenie: This paper proposes a frequencydomain method of substructure identification for local health monitoring using substructure isolation method (SIM). The first key step of SIM is the numerical construction of the isolated substructure, which is a virtual and independent structure that has the same physical parameters as the real substructure. Damage identification and local monitoring can be then performed using the responses of the simple isolated substructure and any of the classical methods aimed originally at global structural analysis. This paper extends the SIM to frequency domain, which allows the computational efficiency of the method to be significantly increased in comparison to time domain. The massspring numerical model is used to introduce the method. Two aluminum beams with the same substructure are then used in experimental verification. In both cases the method performs efficiently and accurately. Słowa kluczowe: structural health monitoring (SHM), damage identification, substructuring frequency domain, boundary Afiliacje autorów:
 20p.  
17.  Chen G.Y.^{♦}, Codemard C.A.^{♦}, Lewis R.J.^{♦}, Jankowski Ł., Chan J.S.^{♦}, Gorman P.M^{♦}, Zervas M.N.^{♦}, Enhanced responsivity with skew ray excitation of reflection and transmissiontype refractometric sensors, OPTICS LETTERS, ISSN: 01469592, DOI: 10.1364/OL.39.003822, Vol.39, No.13, pp.38223825, 2014 Streszczenie: The responsivity of optical fibers to refractive index can be enhanced using highorder skew rays compared with using meridional rays. Skew rays can have a much higher number of reflections with increased interaction length along the core–cladding interface, which gives rise to stronger interactions with the external medium. Reflection/transmissiontype refractometric sensors based on twincoupledcore and multimode fibers showed one/two orders of magnitude increase in responsivity with skew ray excitation. The responsivity and sensitivity for the two types are ∼2000%/RIU, ∼1400%/RIU, and 4.9×10−5 RIU, 7.0×10−5 RIU, respectively. Słowa kluczowe: Fiber optics sensors, Fiber properties, Remote sensing and sensors, Propagation, Biological sensing and sensors Afiliacje autorów:
 40p.  
18.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Substructure isolation and damage identification using free responses, Science China Technological Sciences, ISSN: 16747321, DOI: 10.1007/s1143101456221, Vol.57, No.9, pp.16981706, 2014 Streszczenie: Structural health monitoring (SHM) has become a hot and intensively researched field in civil engineering. Thereinto, damage identification play an important role in maintaining structural integrity and safety. Many effective methods have been proposed for damage identification. However, accurate global identification of large realworld structures is not easy due to their complex and often unknown boundary conditions, nonlinear components, insensitivity of global response to localized damages, etc. Furthermore, global identification often requires lots of sensors and involves large number of unknowns. This is costly, rarely feasible in practice, and usually yields severely illconditioned identification problems. Substructuring approach is a possible solution: substructuring methods can focus on local small substructures; they need only a few sensors placed on the substructure and yield smaller and numerically much more feasible identification problems. This paper proposed an improved substructure method using local free response for substructure damage identification. The virtual supports are constructed by Substructure Isolation Method (SIM) using the linear combination of the substructural responses. The influence of the global errors is isolated by adding the virtual supports on the main degree of freedoms (DOFs) of the substructure. Through the correlation analysis, the substructural modes are selected and used for damage identification of the substructure. A plain model of cable stayed bridge is used for the verification of the proposed method. Słowa kluczowe: structural health monitoring (SHM), damage identification, substructure, cable stayed bridge, free response Afiliacje autorów:
 25p.  
19.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Structural health monitoring based on combined structural global and local frequencies, MATHEMATICAL PROBLEMS IN ENGINEERING, ISSN: 1024123X, DOI: 10.1155/2014/405784, Vol.2014, pp.405784113, 2014 Streszczenie: This paper presents a parameter estimation method for Structural Health Monitoring based on the combined measured structural global frequencies and structural local frequencies. First, the global test is experimented to obtain the low order modes which can reflect the global information of the structure. Secondly, the mass is added on the member of structure to increase the local dynamic characteristic and to make the member have local primary frequency, which belongs to structural local frequency and is sensitive to local parameters. Then the parameters of the structure can be optimized accurately using the combined structural global frequencies and structural local frequencies. The effectiveness and accuracy of the proposed method are verified by the experiment of a space truss. Afiliacje autorów:
 25p.  
20.  Zhang Q., Duan Z.^{♦}, Jankowski Ł., Substructure damages and excitations identification using measured response, APPLIED MECHANICS AND MATERIALS, ISSN: 16627482, DOI: 10.4028/www.scientific.net/AMM.501504.843, Vol.501504, pp.843846, 2014 Streszczenie: This paper proposes a methodology on simultaneous identification of substructure excitation and damage. Structural damages are simulated by virtual distortions which are computed together with unknown excitations using the measured responses through the intact isolated substructure model; the damage extent and type is then recovered by a comparison of the virtual and actual distortions. Unknown factors are reduced greatly which allows the method to be applied on practical complex structure. The computational cost is cutoff sharply. A damaged nonlinearity aluminum beam is used in the experimental verification. Both load and damage are successfully identified. Słowa kluczowe: Damage Identification, Load Identification, Structural Health Monitoring (SHM), Substructure Afiliacje autorów:
 7p.  
21.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, An online substructure identification method for local structural health monitoring, SMART MATERIALS AND STRUCTURES, ISSN: 09641726, DOI: 10.1088/09641726/22/9/095017, Vol.22, No.9, pp.095017111, 2013 Streszczenie: This paper proposes a substructure isolation method, which uses time series of measured local response for online monitoring of substructures. The proposed monitoring process consists of two key steps: construction of the isolated substructure, and its identification. The isolated substructure is an independent virtual structure, which is numerically isolated from the global structure by placing virtual supports on the interface. First, the isolated substructure is constructed by a specific linear combination of time series of its measured local responses. Then, the isolated substructure is identified using its local natural frequencies extracted from the combined responses. The substructure is assumed to be linear; the outside part of the global structure can have any characteristics. The method has no requirements on the initial state of the structure, and so the process can be carried out repetitively for online monitoring. Online isolation and monitoring is illustrated in a numerical example with a frame model, and then verified in a cantilever beam experiment. Afiliacje autorów:
 40p.  
22.  Zhang Q., Jankowski Ł., Duan Z.^{♦}, Simultaneous identification of moving vehicles and bridge damages considering road rough surface, MATHEMATICAL PROBLEMS IN ENGINEERING, ISSN: 1024123X, DOI: 10.1155/2013/963424, Vol.2013, pp.963424112, 2013 Streszczenie: A method for the simultaneous identification of moving vehicles and the damages of the supporting structure from measured responses is presented. A twoaxle vehicle model with two degrees of freedom (DOF) is adopted. The extent of the damage and the vehicle parameters were chosen as the optimisation variables, which allow ill conditioning to be avoided and decrease the number of sensors required. The identification is performed by minimising the distance between the measured responses and the computed responses to given optimisation variables. The virtual distortion method (VDM) was used, such that the response of the damaged structure can be computed from comparison with the intact structure subjected to the same vehicle excitation and to the responsecoupled virtual distortions. These are related to the optimisation variables by the system impulse response matrix and are expressed by a linear system, which allowed both types of optimisation variables to be treated in a unified way. The numerical cost is reduced by using a moving influence matrix. The adjoint variable method is used for fast sensitivity analysis. A threespan bridge numerical example is presented, where the identification was verified with 5% root mean square (RMS) measurement, and model, error whilst also considering the surface roughness of the road. Afiliacje autorów:
 30p.  
23.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Structural damage identification by adding virtual masses, STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION, ISSN: 1615147X, DOI: 10.1007/s0015801208790, Vol.48, No.1, pp.5972, 2013 Streszczenie: This paper presents a method for damage identification by adding virtual masses to the structure in order to increase its sensitivity to local damages. The main concept is based on the Virtual Distortion Method (VDM), which is a fast structural reanalysis method that employs virtual distortions or pseudo loads to simulate structural modifications. In this paper, the structure with an added virtual mass is called the virtual structure. First, the acceleration frequency response of the virtual structure is constructed numerically by the VDM using local dynamic data measured only by a single excitation sensor and a single acceleration sensor. Second, the value of the additional mass is determined via sensitivity analysis of the constructed frequency responses of the virtual structure with respect to damage parameters; only the natural frequencies with high sensitivity are selected. This process is repeated for all the considered placements of the virtual mass. At last, the selected natural frequencies of all the virtual structures are used together for damage identification of the real structure. A finite element (FE) model of a plane frame is used to introduce and verify the proposed method. The damage can be identified precisely and effectively even under simulated 5 % Gaussian noise pollution. Słowa kluczowe: Structural health monitoring (SHM), Damage identification, Virtual distortion method (VDM), Virtual mass, Sensitivity analysis Afiliacje autorów:
 30p.  
24.  Hou J.^{♦}, Ou J.^{♦}, Jankowski Ł., Structural damage identification using additional virtual supports, JOURNAL OF VIBRATION AND SHOCK, ISSN: 10003835, Vol.32, No.10, pp.118129, 2013 Streszczenie: 针对土木工程中实测模态相对较少，很难进行大型结构的损伤识别的困难，提出附加虚拟支座的损伤识别方法。该方法利用约束子结构方法在结构上附加虚拟支座来增加结构形式的方法，增加识别模态的数量，从而实现结构的准确损伤识别。约束子结构方法的基本思想是通过响应的卷积组合为零将传感器转化为虚拟支座。将附加虚拟支座后的结构定义为虚拟结构，每个虚拟支座对应一个虚拟结构，那么在结构上不同位置附加虚拟支座，则可以获得多个虚拟结构的模态；联合所有虚拟结构和对应的频率即可准确快速的识别出整体结构的损伤。最后通过三层空间框架模型验证方法的有效性。 Słowa kluczowe: 结构健康监测, 损伤识别, 约束子结构方法, 灵敏度分析, 频率 Afiliacje autorów:
 
25.  Zhang Q., Duan Z.^{♦}, Jankowski Ł., Fast simultaneous identification of structural damages and loads, JOURNAL OF VIBRATION AND SHOCK, ISSN: 10003835, Vol.32, No.2, pp.3338, 2013 Streszczenie: 本文仅以损伤因子为优化变量，提出一种结构损伤和荷载同步识别的方法。首先通过时域荷载识别的方法将未知荷载转化为损伤因子的函数，将近似荷载作用下的结构响应和实测响应的平方距离作为目标函数，从而降低了需要识别未知参数的数目；然后在目标函数的计算过程中，利用虚拟变形法（VDM）可进行结构快速重分析的思想，快速构造给定损伤因子下系统的脉冲响应，避免每步迭代重新集装系统矩阵，并通过荷载形函数方法进一步提高荷载识别的效率；最后利用二次多项式插值近似结构每个时刻的响应方法和推导对应目标函数的梯度表达式来提高优化搜索的速度。本文利用刚架模型进行数值模拟，准确识别了结构中柱子单元刚度损伤、附加质量以及梁上的未知移动荷载，并通过一个悬臂梁试验进一步验证所提出方法的准确性和可行性。 Słowa kluczowe: 结构健康监测, 荷载识别, 损伤识别, 虚拟变形法(VDM) Afiliacje autorów:
 
26.  Hou J.^{♦}, Ou J.^{♦}, Jankowski Ł., Model updating experiment of space truss using global and local dynamic information, JOURNAL OF VIBRATION AND SHOCK, ISSN: 10003835, Vol.32, No.16, pp.100105, 2013 Streszczenie: 由于土木工程结构的复杂性、传感器测点的有限性以及局部损伤的不敏感性等问题，大型结构的模型修正存在一定困难。针对空间桁架结构，为克服上述问题，对其进行整体和局部的动力测试试验，然后联合实测的结构整体和局部动态信息进行模型修正：首先进行空间桁架整体的动力测试试验，获得反应整体特性的低阶模态；然后为了提高局部杆件的动态特性，在杆件上附加一定质量，获得附加质量后杆件的局部主频率，并在各类杆件中选取一定数目进行动态测试；最后联合所有实测结构整体的低阶模态和杆件的局部主频率，对空间桁架结构进行模型修正。修正后的模态参数与实测模态吻合良好，验证了方法的有效性。 Słowa kluczowe: 结构健康监测, 模型修正, 桁架, 频率, 振型 Afiliacje autorów:
 
27.  Hou J.^{♦}, Ou J.^{♦}, Jankowski Ł., The experiment of substructure isolation and identification using local time series, Engineering Mechanics, ISSN: 10004750, DOI: 10.6052/j.issn.10004750.2011.10.0722, Vol.30, No.4, pp.129135, 2013 Streszczenie: 针对大型复杂结构的整体监测常常面临测量信息不足等困难,提出只利用局部动态响应进行子结构损伤识别的约束子结构方法。约束子结构方法是通过子结构响应的卷积组合限制子结构边界的响应为零,来实现施加虚拟支座,从而将子结构分离出整体,然后利用构造的相应子结构内部响应,进行子结构损伤识别。该文利用先分段提取结构响应的子时间序列,再延时排列Toeplitz矩阵的方式,使基于不同响应的构造约束子结构的方程具有相同表达式,统一了约束子结构方法的基本思想。通过测量悬臂梁的局部动力响应,利用局部响应的时间序列实现了子结构的快速准确地分离和识别,验证了方法的实用性和有效性。 Słowa kluczowe: 结构健康监测, 损伤识别, 子结构, 时间序列, 脉冲响应 Afiliacje autorów:
 
28.  Zhang Q., Hou J.^{♦}, Duan Z.^{♦}, Jankowski Ł., Substructural virtual distortion method for damage identification, Engineering Mechanics, ISSN: 10004750, DOI: 10.6052/j.issn.10004750.2012.08.0613, Vol.30, No.12, pp.176182, 2013 Streszczenie: 针对大型土木结构损伤识别优化效率低的问题，提出了子结构虚拟变形方法。虚拟变形方法是一种结构 Afiliacje autorów:
 
29.  Suwała G., Biczyk J.^{♦}, Jankowski Ł., Nonparametric identification of added masses in frequency domain: a numerical study, Prace IPPT  IFTR Reports, ISSN: 22993657, Vol.4f, pp.16, 2013 Streszczenie: This paper presents a theoretical derivation and reports on a numerical verification of a modelfree method for identification of added masses in truss structures. No parametric numerical model of the monitored structure is required, so that there is no need for initial model updating and fine tuning. This is a continuation and an improvement of a previous research that resulted in a timedomain identification method, which was tested to be accurate but very timeconsuming. A general methodology is briefly introduced, including the inverse problem, and a numerical verification is reported. The aim of the numerical study is to test the accuracy of the proposed method and its sensitivity to various parameters (such as simulated measurement noise and decay rate of the exponential FFT window) in a numerically controlled environment. The verification uses a finite element model of the same real structure that was tested with the timedomain version of the approach. A natural further step is a lab verification based on experimental data. Afiliacje autorów:
 
30.  Zhang Q., Jankowski Ł., Duan Z.^{♦}, Simultaneous identification of excitation time histories and parametrized structural damages, MECHANICAL SYSTEMS AND SIGNAL PROCESSING, ISSN: 08883270, DOI: 10.1016/j.ymssp.2012.06.018, Vol.33, pp.5668, 2012 Streszczenie: This paper presents and experimentally verifies an effective method for simultaneous identification of excitations and damages, which are two crucial factors in structural health monitoring and which often coexist in practice. The unknowns are identified by minimizing a timedomain square distance between the measured and the computed responses. Even though both damage and excitation are unknown, only damage parameters are treated here as the optimization variables: given the damage, the excitation is uniquely determined from the measured responses. As a result, all unknowns are of the same type, which allows standard optimization algorithms to be used and obviates the need for twostep procedures. The sensitivity analysis is facilitated by interpolating in each iteration the relation between structural responses and damage parameters. The numerical costs are further decreased by the fast reanalysis approach of the virtual distortion method (VDM), which is used to compute exact impulse responses of the damaged structure. The proposed methodology is verified both numerically (using a multispan frame) and experimentally (using a cantilever beam). Stiffnessrelated damages and massrelated modifications are identified successfully together with the three tested types of external excitation. Słowa kluczowe: Structural health monitoring, Load identification, Damage identification, Virtual distortion method (VDM) Afiliacje autorów:
 45p.  
31.  Suwała G., Jankowski Ł., A modelfree method for identiﬁcation of mass modiﬁcations, STRUCTURAL CONTROL AND HEALTH MONITORING, ISSN: 15452255, DOI: 10.1002/stc.417, Vol.19, No.2, pp.216230, 2012 Streszczenie: In this paper, a modelfree methodology for offline identification of modifications of structural mass is proposed and verified experimentally. The methodology of the virtual distortion method is used: the modifications are modeled by the equivalent pseudoloads that act in the related degrees of freedom of the unmodified structure; their influence on the response is computed using a convolution of the pseudoloads with the experimentally obtained local impulse responses. As a result, experimentally measured data are directly used to model the response of the modified structure in a nonparametric way. The approach obviates the need for a parametric numerical model of the structure and for laborious initial updating of its parameters. Moreover, no topological information about the structure is required, besides potential locations of the modifications. The identification is stated as a problem of minimization of the discrepancy between the measured and the modeled responses of the modified structure. The formulation allows the adjoint variable method to be used for a quick first and secondorder sensitivity analysis, so that Hessianbased optimization algorithms can be used for fast convergence. The proposed methodology was experimentally verified using a 3D truss structure with 70 elements. Mass modifications in a single node and in two nodes were considered. Given the initially measured local impulse responses, a single sensor and single excitation were sufficient for the identification. Słowa kluczowe: mass identification, structural health monitoring (SHM), virtual distortion method (VDM), modelfree, nonparametric modeling, adjoint variable method Afiliacje autorów:
 30p.  
32.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Experimental study of the substructure isolation method for local health monitoring, STRUCTURAL CONTROL AND HEALTH MONITORING, ISSN: 15452255, DOI: 10.1002/stc.443, Vol.19, No.4, pp.491510, 2012 Streszczenie: This paper extends and studies experimentally the substructure isolation method. Local health monitoring is significant for large and complex structures, since it costs less and can be easily implemented compared with global analysis. In contrast to other substructuring methods, in which the substructure is separated from the global structure, but coupled to it via the interface forces, the substructure isolation method isolates the substructure into an independent structure by placing virtual fixed supports on the interface. Model updating or damage identification can be then performed locally and precisely using the constructed responses of the isolated substructure and any of the existing methods aimed originally at global identification. This paper discusses and further extends the approach to improve its performance in real applications. A new type of virtual interface support (free support) is proposed for isolation. Relaxation of the original requirements concerning the type and placement of the isolating excitations is discussed. Previously, the method relied on the linearity of the global structure; here, only the substructure is required to be linear, the global structure besides the substructure can be nonlinear, yielding, changing or unknown. A damaged cantilever beam is used in the experimental study. Up to three modified global structures with the same substructure are used to test the robustness of the isolation with respect to unknown modifications and nonlinearities of the outside structure. Two typical global health monitoring methods are applied at the substructural level. A comparison with the results obtained from a generic substructure separation method is offered. Słowa kluczowe: Structural Health Monitoring (SHM), substructure isolation method, substructural identification, virtual distortion method (VDM), local monitoring, virtual supports Afiliacje autorów:
 30p.  
33.  Hou J.^{♦}, Ou J.^{♦}, Jankowski Ł., The study and experiment of substructure damage identification based on local primary frequency, Engineering Mechanics, ISSN: 10004750, DOI: 10.6052/j.issn.10004750.2010.12.0928, Vol.29, No.9, pp.99105, 2012 Streszczenie: 针对大型复杂结构的整体监测常常面临测量信息不足等困难,提出只利用局部动态响应进行子结构损伤识别的局部主频率方法.子结构的局部主频率指：如果整体模态中含有以局部子结构位移为主的模态,即等价于在局部激励作用下,整体结构的振动主要体现为子结构的振动,并且主要以这阶局部模态振动为主,那么对应的该阶频率即定义为子结构的局部主频率.局部主频率主要反映子结构的局部特性,对子结构损伤的灵敏度高,所以只利用局部主频率就可以识别子结构.当子结构特征不明显时,提出通过附加质量使子结构具有局部主频率的有效方法.该文进行了大型空间桁架的局部动力测试试验,试验中通过附加质量使杆件子结构具有局部主频率,并能准确地识别出杆件损伤的位置和程度. Słowa kluczowe: 结构健康监测, 损伤识别, 子结构, 模态分析, 频率响应 Afiliacje autorów:
 
34.  Zhang Q., Duan Z.^{♦}, Jankowski Ł., The study on simultaneous identification of structural damages and loads, Engineering Mechanics, ISSN: 10004750, DOI: 10.6052/j.issn.10004750.2011.05.0275, Vol.29, No.12, pp.316321, 2012 Streszczenie: 针对结构中同时存在未知损伤和荷载的情况，基于虚拟变形法(VDM)发展一种两者共同识别的时域方法。VDM方法利用虚拟变形模拟结构损伤，可快速计算模型改变后的响应。该文首先结合有限元理论把VDM方法拓展到具有多个单元变形的结构中；然后考虑结构存在未知荷载时，利用未损伤理论模型同时识别荷载和虚拟变形，继而由虚拟变形和单元实际变形的关系来识别判断损伤类型和识别损伤大小；最后通过一个悬臂梁的试验进行方法验证，试验中未知荷载和损伤(包括其类型和大小)均能够被有效识别，并利用提出的移动时间窗和荷载形函数方法实现损伤与荷载的在线识别。 Słowa kluczowe: 结构健康监测, 虚拟变形法(VDM), 荷载识别, 损伤识别, 荷载形函数 Afiliacje autorów:
 
35.  Zhang Q., Duan Z.^{♦}, Jankowski Ł., Parameter identification of moving vehicles considering road roughness of bridge, Journal of Vibration Engineering, ISSN: 10044523, Vol.25, No.2, pp.146153, 2012 Streszczenie: 基于虚拟变形(VDM)方法中移动动态影响矩阵的概念,利用双自由度质量弹簧阻尼模型模拟移动车辆,系统推导和阐述了车桥耦合系统中粗糙路面上移动体参数的识别方法。以移动体参数的修正因子为优化变量,通过最小化桥体结构实测响应和计算响应的平方距离进行识别,识别精度高,对噪声鲁棒性强,且较少的传感器就能识别多个移动体参数。利用移动动态影响矩阵,每步优化中无需时时重构系统参数矩阵,计算效率高。利用一个三跨连续梁模型验证该方法的有效性,在5%的噪声影响下,利用一个传感器可以准确地识别多个移动体参数和移动荷载。此外,通过比较平坦路面与粗糙路面上的移动体参数的识别方法和结果,结合车体参数的灵敏度分析,说明了路面粗糙度、移动体参数对结构响应的影响及不同情况下参数识别中优化变量的选取原则。 Słowa kluczowe: 结构健康监测, 移动车辆(荷载)识别, 虚拟变形法(VDM), 影响矩阵, 粗糙路面 Afiliacje autorów:
 
36.  Jilin Hou^{♦}, Jankowski Ł., Jinping Ou^{♦}, A substructure isolation method for local structural health monitoring, STRUCTURAL CONTROL AND HEALTH MONITORING, ISSN: 15452255, DOI: 10.1002/stc.389, Vol.18, pp.601618, 2011 Streszczenie: This paper describes an effective method of substructure isolation for local structural health monitoring (SHM). In practice, often only a small part of a larger structure is critical and needs monitoring. However, typical lowfrequency SHM methods require modeling and analysis of the global structure, which can be costly, timeconsuming and errorprone. The proposed approach is based on the virtual distortion method (VDM) and uses force distortions to model fixed supports in the boundary nodes to isolate the considered substructure from influences of the rest of the structure. Therefore, given an excitation of the substructure and the measured response of the global structure, the response of the substructure treated as fixed supported can be computed. Localonly monitoring is then possible using virtually any of the existing methods. However, consistently with the isolation methodology, strain distortions are used here for modeling of damages of the isolated substructure. The discrete adjoint variable method is used for the first time within the framework of the VDM in order to perform fast analytical sensitivity analysis and improve the computational effectiveness of the damage identification by one order of magnitude. A numerical example of a frametruss with 5 and 10% noise level and an experiment of a cantilever beam are presented to validate the isolation methodology. Słowa kluczowe: substructure isolation, damage identification, virtual distortion method (VDM), structural health monitoring, adjoint variable method Afiliacje autorów:
 30p.  
37.  Zhang Q., Duan Z.^{♦}, Jankowski Ł., Wang F.^{♦}, Experimental validation of a fast dynamic load identification method based on load shape function, JOURNAL OF VIBRATION AND SHOCK, ISSN: 10003835, Vol.30, No.9, pp.98102, 154, 2011 Streszczenie: 在动态荷载识别中常常由于矩阵的病态性影响识别的精度，利用有限元理论中的形函数逼近荷载曲线，将识别离散的荷载历程转化为计算有限的形函数权重，从而显著改善反卷积法识别荷载中存在的采样时间长或采样频率高时数值求解困难的问题；并能改善反问题的病态性，提高对噪音的鲁棒性。一个连续梁的数值算例比较验证了该方法在5%的高斯噪声影响下能精确地识别未知荷载。悬臂梁试验中，通过实测的结构动态响应，在移动时间窗内利用荷载形函数方法可以实现激励的在线识别。 Słowa kluczowe: 结构健康监测, 荷载识别, 在线识别, 反卷积法, 形函数 Afiliacje autorów:
 
38.  Zhang Q., Duan Z.^{♦}, Jankowski Ł., Moving mass identification of vehiclebridge coupled system based on virtual distortion method, Chinese Journal of Theoretical and Applied Mechanics, ISSN: 04591879, DOI: 10.6052/0459187920113lxxb2009481, Vol.43, No.3, pp.598610, 2011 Streszczenie: 利用双自由度质量弹簧阻尼模型模拟移动车辆, 并基于虚拟变形(VDM)方法的结构快速重分 析思想, 提出一种车桥耦合系统的移动质量快速识别的有效方法. 该方法以双自由度车体模 型的质量为变量, 通过最小化桥体结构实测响应和计算响应的平方距离来识别移动质量 (载荷), 避免了识别载荷时常遇到的病态问题, 对噪声鲁棒性强, 且需要传感器信息少. 每步优化 中, 利用在VDM方法基础上提出的移动动态影响矩阵概念, 无需时时重构车桥耦合系统的时 变系统参数矩阵, 显著提高了计算效率. 利用数值框架梁模型, 通过比较不同车辆简化模型 对移动体质量及等效移动载荷的识别效果, 验证了该方法的可行性和有效性, 即使在5% 的噪声影响下, 利用一个传感器可以准确地识别多个移动体的质量. Słowa kluczowe: 结构健康监测, 移动车辆识别, 结构重分析, 虚拟变形法, 影响矩阵 Afiliacje autorów:
 
39.  Zhang Q., Jankowski Ł., Duan Z.^{♦}, Identification of coexistent load and damage, STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION, ISSN: 1615147X, DOI: 10.1007/s0015800904211, Vol.41, pp.243253, 2010 Streszczenie: Load reconstruction and damage identification are crucial problems in structural health monitoring. However, it seems there is not much investigation on identification of coexistent load and damage, although in practice they usually exist together. This paper presents a methodology to solve this problem based on the Virtual Distortion Method. A damaged structure is modeled by an equivalent intact structure subjected to the same loads and to virtual distortions which model the damages. The measured structural response is used to identify the loads, the distortions and to recover the stressstrain relationship of the damaged elements. This way both the damage type and extent are identified. The approach can be used offline and online by repetitive applications in a moving time window. A numerical experiment of a truss with 5% measurement error validates that the two tested damage types (constant stiffness reduction and breathing crack) can be identified along with the loads. Słowa kluczowe: Structural health monitoring, Load identification, Damage identification, Virtual Distortion Method (VDM) Afiliacje autorów:
 32p.  
40.  Zhang Q., Jankowski Ł., Duan Z.^{♦}, Simultaneous identification of moving masses and structural damage, STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION, ISSN: 1615147X, DOI: 10.1007/s0015801005284, Vol.42, pp.907922, 2010 Streszczenie: A method for simultaneous identification of moving masses and damages of the supporting structure from measured responses is presented. The interaction forces between the masses and the structure are used as excitation. Masses and damage extents are used as the optimization variables; compared to the approaches based on identification of the interaction forces, it allows illconditioning to be avoided and decreases the number of required sensors. The virtual distortion method is used; the damaged structure is modeled by the intact structure subjected to responsecoupled virtual distortions and moving forces. These are related to the optimization variables via a linear system, which allows the optimization variables of both kinds to be treated in a unified way. A moving dynamic influence matrix is introduced to reduce the numerical costs. The adjoint variable method is used for fast sensitivity analysis. A numerical experiment of a threespan beam with 10% rms measurement error and three types of model errors is presented. Słowa kluczowe: Moving load identification, Damage identification, Mass identification, Virtual distortion method (VDM), Structural health monitoring (SHM) Afiliacje autorów:
 32p.  
41.  Zhang Q., Duan Z.^{♦}, Jankowski Ł., Moving mass identification based on Virtual Distortion Method, Journal of Vibration Engineering, ISSN: 10044523, Vol.23, No.5, pp.494501, 2010 Streszczenie: 在车桥耦合系统的移动质量（荷载）识别反问题中,识别移动质量会面临重构系统、优化缓慢的问题;而若直接识别移动荷载常常会遇到病态问题且对噪音敏感。针对这些缺陷,根据虚拟变形法（VDM）的结构快速重分析思想,提出移动动态影响矩阵,实现利用较少的传感器即可快速而准确地识别移动质量（荷载）。以移动质量为优化变量,避免了识别荷载常遇到的病态问题,对噪音鲁棒性强;且需要传感器信息少。每步优化中,利用移动动态影响矩阵,无需时时重构车桥耦合系统的时变系统参数矩阵,优化效率高。VDM方法的思想是将实际结构的响应计算转化为初始结构模型在相同外荷载作用下的响应,与在结构模型发生改变的位置施加相关的虚拟变形或虚拟力引起的响应的线性叠加。通过简支梁模型和框架梁模型验证了该方法的可行性和有效性,即使在5%的噪声影响下,利用一个传感器就可以很好地识别多个移动质量。 Słowa kluczowe: 结构健康监测, 结构重分析, 影响矩阵 Afiliacje autorów:
 
42.  Jankowski Ł., Offline identification of dynamic loads, STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION, ISSN: 1615147X, DOI: 10.1007/s0015800802490, Vol.37, No.6, pp.609623, 2009 Streszczenie: This paper considers offline identification of spatial and temporal characteristics of a dynamic load, and is focused on the case of a limited number of sensors. Both elastic and elastoplastic structural behaviours are taken into account. The identification is performed offline, based on optimisation of modelled local structural responses, and—in the case of limited number of sensors—identifies an observationally equivalent load, which in a given sense optimally approximates the actual load. Compared to previous researches this approach allows to identify general dynamic loads of unknown locations, including multiple impacts and moving loads, and gives more insight into the identification process by distinguishing between the reconstructible and unreconstructible load components. Additionally, the problem of optimum sensor location is discussed. Słowa kluczowe: Load identification, Inverse dynamics, Elastoplastic structures, Black box, Forensic engineering Afiliacje autorów:
 32p.  
43.  Mikułowski G., Jankowski Ł., Adaptive Landing Gear: optimum control strategy and potential for improvement, SHOCK AND VIBRATION, ISSN: 10709622, DOI: 10.3233/SAV20090460, Vol.16, No.2, pp.175194, 2009 Streszczenie: An adaptive landing gear is a landing gear (LG) capable of active adaptation to particular landing conditions by means of controlled hydraulic force. The objective of the adaptive control is to mitigate the peak force transferred to the aircraft structure during touchdown, and thus to limit the structural fatigue factor. This paper investigates the ultimate limits for improvement due to various strategies of active control. Five strategies are proposed and investigated numerically using a~validated model of a real, passive landing gear as a reference. Potential for improvement is estimated statistically in terms of the mean and median (significant) peak strut forces as well as in terms of the extended safe sinking velocity range. Three control strategies are verified experimentally using a laboratory test stand. Słowa kluczowe: Adaptive landing gear, adaptive impact absorption, shock absorber, load mitigation Afiliacje autorów:
 20p.  
44.  Suwała G., Jankowski Ł., A modelless method for added mass identification, SOLID STATE PHENOMENA, ISSN: 10120394, DOI: 10.4028/www.scientific.net/SSP.147149.570, Vol.147149, pp.570575, 2009 Streszczenie: This paper present and validates experimentally a modelless methodology for offline identification of modifications of nodal masses. The proposed approach is entirely based on experimentally measured data; hence no numerical modeling and tedious finetuning of the model are necessary. The influence of the added mass is modeled using virtual distortion forces and experimentally obtained system transfer matrices. The identification amounts to solving an optimization problem of minimizing the mean square distance between measured and modeled structural responses, the latter is based on previously recorded responses of the unaffected structure. Słowa kluczowe: mass identification, modelless SHM, virtual distortion method (VDM), inverse dynamics Afiliacje autorów:
 20p.  
45.  Szolc T., Jankowski Ł., Active control of transient torsional vibrations due to runup of a rotor machine driven by the electric motor, VIBRATIONS IN PHYSICAL SYSTEMS, ISSN: 08606897, Vol.23, pp.341346, 2008 Streszczenie: In the paper active control of transient torsional vibrations induced by the electric motor during runups of the radial compressor drive system is performed by means of couplings with the magnetorheological fluid. The main purpose of these studies is a minimisation of vibration amplitudes in order to increase the fatigue durability of the most responsible elements. The theoretical investigations are based on a hybrid structural model of the vibrating mechanical system and sensitivity analysis of the response with respect to the damping characteristics of the control couplings. Słowa kluczowe: active control, transient vibrations, drive system, electric motor Afiliacje autorów:
 
46.  Jankowski Ł., Wikło M., HolnickiSzulc J., Robust postaccident reconstruction of loading forces, KEY ENGINEERING MATERIALS, ISSN: 16629795, DOI: 10.4028/www.scientific.net/KEM.347.659, Vol.347, pp.659664, 2007 Streszczenie: The paper presents a novel methodology for robust postaccident reconstruction of spatial and temporal characteristics of the load. The methodology is based on analysis of local structural response, and identifies an observationally equivalent load, which in a given sense optimally approximates the real load. Compared to previous researches this approach allows to use a limited number of sensors to reconstruct general dynamic loads of unknown location including multiple impacts and moving loads. Additionally, the problem of optimum sensor location is studied. Słowa kluczowe: impact identification, inverse dynamics, smart systems, structural health monitoring Afiliacje autorów:

Lista ostatnich monografii
1. 323  Jankowski Ł., Dynamic load identification for structural health monitoring, Rozprawa habilitacyjna, IPPT Reports on Fundamental Technological Research, pp.1280, 2013 
2. 73  Jankowski Ł., Modelling and simulation of light propagation in nonaged and aged stepindex polymer optical fibres, Wirtschaftsverlag NW Verlag für Neue Wissenschaft, pp.1137, 2005 
Lista rozdziałów w ostatnich monografiach
1. 349  Jankowski Ł., HolnickiSzulc J., Świercz A., Mróz M.^{♦}, Kołakowski P., Monitorowanie obciążeń i stanu technicznego konstrukcji mostowych, rozdział: Numeryczne metody identyfikacji parametrów konstrukcji, IPPT Reports on Fundamental Technological Research, pp.109159, 2014  
2. 166  Jankowski Ł., Bednarek T., Sosnowski W., Knowledge acquisition for hybrid systems of risk assessment and critical machinery diagnosis, rozdział: Selected topics in identification of dynamic loads, Silesian University of Technology (Gliwice), Moczulski W., Ciupke K. (Eds.), pp.357404, 2008  
3. 196  Pawłowski P.K., Mikułowski G., Graczykowski C., Ostrowski M., Jankowski Ł., HolnickiSzulc J., Smart technologies for safety engineering, rozdział: Adaptive impact absorption, Wiley, HolnickiSzulc J. (Ed.), pp.153213, 2008  
4. 197  Jankowski Ł., Sekuła K., Błachowski B., Wikło M., HolnickiSzulc J., Smart technologies for safety engineering, rozdział: Dynamic load monitoring, Wiley, HolnickiSzulc J. (Ed.), pp.105151, 2008  
5. 202  Wikło M., Jankowski Ł., Mróz M.^{♦}, HolnickiSzulc J., Smart technologies for safety engineering, rozdział: VDMBased remodeling of adaptive structures exposed to impact loads, Wiley, HolnickiSzulc J. (Ed.), pp.215249, 2008 
Prace konferencyjne
1.  Gawlicki M., Jankowski Ł., Multiobjective optimization for identification of a moving load path, SMART 2019, 9th ECCOMAS Thematic Conference on Smart Structures and Materials, 20190708/0711, Paris (FR), pp.215222, 2019 Streszczenie: This contribution presents an approach for indirect identification of the 2D path of a moving load. A multicriterial formulation is proposed, where one objective function quantifies the mismatch between the measured and the simulated structural response. The second objective function expresses the natural expectation that the paths of moving loads are continuous and relatively smooth, and it expresses thus a certain splinebased measure of the geometric regularity of the path. The Pareto front is determined in a local evolutionary search and used to strike the balance between the response fit and the geometric regularity of the path. The approach is tested in a laboratory experimental setup of a plate loaded by a linefollower robot. It is found that the implementation of the smoothnessbased objective has a regularizing influence on the identification results: it reveals and emphasizes the actual geometrical character of the identified paths. Słowa kluczowe: Trajectory Identification, Moving Load, Inverse Problem, Structural Health Monitoring, Multicriterial Optimization Afiliacje autorów:
 
2.  Błachowski B., Tauzowski P., Świercz A., Jankowski Ł., Topology optimization approach for dense sensor network distribution over large bridge structures, SMART 2019, 9th ECCOMAS Thematic Conference on Smart Structures and Materials, 20190708/0711, Paris (FR), pp.284290, 2019 Streszczenie: Recent progress in sensing technology and measurement techniques allows a growing number of critical infrastructures to be equipped with Structural Health Monitoring (SHM) systems. Sensors in such SHM systems should be placed in a proper way to facilitate extracting valuable information from the structure under investigation. In the case of relatively simple spatial truss structures, sensors can be located with the aid of classical methods such as Effective Independence (EI) method proposed by Kammer. However, in the case of large structures, which are intended to be equipped with hundreds if not thousands of sensors, other sensor placement methods may be needed. Słowa kluczowe: Optimal sensor placement, Structural parameter identification, Topology optimization Afiliacje autorów:
 
3.  Mikułowski G., Popławski B., Jankowski Ł., An experimental investigation of the prestress accumulation release strategy for local mitigation of structural vibrations, SMART 2019, 9th ECCOMAS Thematic Conference on Smart Structures and Materials, 20190708/0711, Paris (FR), pp.323332, 2019 Streszczenie: This contribution presents an experimental analysis of the control system configuration for a semiactive frame structure. The structure is equipped with a system that implements a Prestress Accumulation Release strategy for mitigation of vibration. A proper distribution of the sensors for monitoring the actual state of the structure is the key factor that determines the overall effectiveness of the applied strategy. The results and findings presented here reveal a set of basic rules dedicated to solving this crucial issue. Słowa kluczowe: Prestress Accumulation Release, Vibration control, Sensor placement, Semiactive structures, Piezoelectric actuation Afiliacje autorów:
 
4.  Ostrowski M., Błachowski B., Jankowski Ł., Pisarski D., Inverse Lyapunov based method for semiactive control of energy transfer between vibration modes, SMART 2019, 9th ECCOMAS Thematic Conference on Smart Structures and Materials, 20190708/0711, Paris (FR), pp.345356, 2019 Streszczenie: This contribution proposes a semiactive control approach for a directed energy transfer between structural vibrational modes. The motivation is the intended localization of the vibration energy in a selected mode for the purpose of energy harvesting and mitigation of structural vibrations. The proposed control strategy aims at the instantaneous maximization of the energy transfer to the target mode. It is based on an untypical approach of dynamic structural reconfiguration and implemented using a semiactively controllable node: a lockable joint. Such a joint, depending on the control signal, can act as a hinge or as a typical frame node. Effectively, it provides thus an on/off ability to control the transfer of bending moments between the adjacent structural elements. The effectiveness of the approach is demonstrated in a numerical example of a plane frame structure. Słowa kluczowe: Modal control, Semiactive control, Lockable joints, Energy harvesting Afiliacje autorów:
 
5.  Popławski B., Mikułowski G., Jankowski Ł., Semiactive decentralized mitigation of randomly excited vibrations in 2D frame structures, SMART 2019, 9th ECCOMAS Thematic Conference on Smart Structures and Materials, 20190708/0711, Paris (FR), pp.357363, 2019 Streszczenie: Semiactive control systems are investigated for more than 40 years, and despite the great progress in this research area, they are still considered to be a complex topic in both theoretical and technical terms. However, their advantages ensure that these control systems remain an extremely attractive subject of scientific and technological development. Słowa kluczowe: Semiactive damping, Vibration damping, Random vibration, Forced vibration Afiliacje autorów:
 
6.  Faraj R., Graczykowski G., Jankowski Ł., HolnickiSzulc J., Adaptable ballscrew inerter for optimal impact absorption, SMART 2019, 9th ECCOMAS Thematic Conference on Smart Structures and Materials, 20190708/0711, Paris (FR), pp.485491, 2019 Streszczenie: For over two decades, inerterbased devices are a subject of research papers, patents and engineering reports. Since 2002, when the inerter was introduced as the missing element of mechanical networks, various applications of the inerter have been proposed. They include solutions for earthquake engineering, suspensions of vehicles, aircraft landing gears and even systems improving walking performance of humanoid robots. In contrast to majority of the inerterbased systems, which are mainly developed for vibration mitigation problems, this paper concerns the inerter as the shockabsorber protecting objects excited by the impact. In particular, adaptive performance of the ballscrew inerter with variable moment of the flywheel inertia is investigated. In order to ensure efficient adaptation of the inerter to various excitation conditions, the single reconfiguration technique, which was successfully applied for pneumatic absorber, is now adjusted and implemented in the proposed inertial system. The contribution consists of the concept introduction, discussion of the mathematical model of the system, theoretical as well as numerical analyses. Results of the presented study show that optimal impact absorption can be obtained in semipassive manner. The properly adjusted geometry of the surface guides for the inertial elements ensure appropriate variability of the flywheel moment of inertia. Variable moment of the flywheel inertia provides optimal deceleration of the amortized object. The calculated moment of inertia depends on the mass of amortized object and friction but it is independent of the impact velocity. Słowa kluczowe: ballscrew inerter, impact absorption, passive absorber, variable inertance, variable moment of inertia, inertial damping Afiliacje autorów:
 
7.  Ahsani S.^{♦}, Deckers E.^{♦}, Zieliński T.G., Jankowski Ł., Claeys C.^{♦}, Desmet W.^{♦}, Absorption enhancement in poroelastic materials by mass inclusions, exploiting the massspring effect, SMART 2019, 9th ECCOMAS Thematic Conference on Smart Structures and Materials, 20190708/0711, Paris (FR), pp.10761084, 2019 Streszczenie: In this paper the possibility of enhancing the absorption coefficient of a poroelastic material using small, elastic mass inclusions in frequencies lower than the quarterwavelength resonance of the porous material is discussed. We show that absorption peaks can be achieved not only by what is known in literature as the trapped mode effect, but also by the resonance of small elastic inclusions at low frequencies, which can be interpreted as a massspring effect. In this work, the inclusion and the porous skeleton is considered elastic and fully coupled to each other, therefore accounting for all types of energy dissipation i.e. viscous, thermal, and structural losses and energy dissipated due to the relative motion of the fluid phase and the frame excited by the resonating inclusion. Additionally, the inclusions are also modeled as motionless and rigid to distinguish between the trapped mode and/or the modified frame mode effect and the massspring effect. Moreover, the distinction between these two effects are explained in more detail by comparing the dissipated energy by each mechanism (viscous, thermal and structural effect). Słowa kluczowe: Metaporous material, BiotAllard poroelastic model, Massspring effect Afiliacje autorów:
 
8.  Błachowski B., Świercz A., Jankowski Ł., Virtual Distortion Method based optimal sensor placement for damage identification, ISMA 2018 / USD 2018, International Conference on Noise and Vibration Engineering / International Conference on Uncertainty in Structural Dynamics, 20180917/0919, Leuven (BE), pp.38153824, 2018 Streszczenie: The paper presents a novel method for sensor placement optimized towards effective identification of structural damages. The derivation of the method is based on the concept of virtual distortions together with information provided by a set of strain gauges. Then, a gradient oriented optimization is applied to identify sensor locations, which are the most sensitive to potential damage scenarios. Steepest descent method is utilized to determine the optimal values of the objective function. Additionally, dependence of the method on the applied excitation signal is discussed. Finally, effectiveness of the proposed methodology is demonstrated on an example of optimal search for sensor placement on a 6bay planar truss structure. Słowa kluczowe: optimal sensor placement, virtual distortion method, damage identification Afiliacje autorów:
 15p.  
9.  Mikułowski G., Popławski B., Wiszowaty R., Mróz A.^{♦}, Jankowski Ł., An investigation on a semiactive damping of forced structural vibrations by means of controllable structural nodes, ISMA 2018 / USD 2018, International Conference on Noise and Vibration Engineering / International Conference on Uncertainty in Structural Dynamics, 20180917/0919, Leuven (BE), pp.189201, 2018 Streszczenie: Vibration mitigation in space structures creates a unique class of a technical problem where resistant for outgassing and nonfluidic solutions are preferable. Additionaly, a vibration induced by timevarying excitations needs to be effectively reduced. The vibration mitigation task is speciffically difficult in the case of light, slender and inherently flexible structures of various types, such as supporting structures, deployable structures, modular structures or widespan skeletal roofing structures. This study presents a concept of a vibration attenuation method based on semiactive joints and dedicated to frame structures under forced vibration excitation. The presented investigation contains an analysis of the problem of the optimal control of a structure fitted with semiactive structural members. Furthermore, an adequate model of the semiactive joints is developed and a numerical example is presented. Finally, the research provides an experimental verification of the developed control algorithms, which is conducted on a test stand in a laboratory environment. Afiliacje autorów:
 15p.  
10.  Gawlicki M., Jankowski Ł., Identification of moving loads using the l1 norm minimization, CMM 2017, 22nd International Conference on Computer Methods in Mechanics, 20170913/0916, Lublin (PL), DOI: 10.1063/1.5019092, Vol.1922, pp.10000719, 2018 Streszczenie: This contribution deals with the inverse problem of indirect identification of moving loads. The identification is performed based on the recorded response of the loaded structure and its numerical model. A specific feature of such problems is a very large number of the degrees of freedom (DOFs) that can be excited and a limited number of available sensors. As a result, unless the solution space is significantly limited, the identification problem is underdetermined: it has an infinite number of exact, observationally indistinguishable solutions. We propose an approach based on the assumption of sparsity of the excitation, which can be expressed in the form of a requirement of a bounded l1 norm of the solution. As long as the loads are sparse, the approach allows them to be freely moving, without the usual assumption of a constant velocity. We first test the approach in a numerical example with 10% rms measurement noise. A good qualitative agreement of the numerical results allows to proceed with experimental investigations, and the moving load identification is then carried out based on the response measured experimentally on a lab test stand. Afiliacje autorów:
 15p.  
11.  Popławski B., Mikułowski G., Suwała G., Jankowski Ł., Optimization of actuator placement for vibration damping in the PrestressAccumulation release control approach, WCSCM, 7th World Conference on Structural Control and Monitoring, 20180722/0725, Qingdao (CN), pp.818827, 2018 Streszczenie: This contribution proposes a quantitative criterion for optimization of actuator placement for the Prestress–Accumulation Release (PAR) strategy of mitigation of vibrations. The PAR strategy is a semiactive control approach that relies on controlled redistribution of modal energy into highfrequency highorder modes, where it is effectively dissipated by means of the natural mechanisms of material damping. The energy transfer is achieved by a controlled temporary removal of selected structural constraints. An example is a shorttime decoupling of rotational degrees of freedom in a frame node, so that the bending moments are no longer transferred between the involved beams. If it such a decoupling is performed at the maximum of the shear/bending strain energy of adjacent beams, it results in an almost instantaneous energy release into highfrequency local vibrations and quick dissipation of energy. We propose and test a quantitative criterion for placement of such actuators. The criterion is based on local modal strain energy that can be released into highorder modes. The numerical time complexity is linear with respect to the number of actuators, which facilitates quick selection of placements in large structures. Słowa kluczowe: semiactive control, damping of vibrations, actuator placement, smart structures, PrestressAccumulation Release (PAR) Afiliacje autorów:
 
12.  Popławski B., Mikułowski G., Mróz A.^{♦}, Jankowski Ł., Decentralized algorithm for semiactive damping of forced vibrations using controllable trussframe nodes, WCSCM, 7th World Conference on Structural Control and Monitoring, 20180722/0725, Qingdao (CN), pp.582590, 2018 Streszczenie: Semiactive systems for mitigation of vibrations proved to be effective in many applications. Their prominent advantage is that they combine strong points of passive and active damping systems. Proper design can ensure their reliability, which is what passive systems are praised for. A high effectiveness in vibration damping links them with active systems. At the same time they do not have many deficiencies of active systems. They are adaptive, so they can stay effective in different environmental conditions, which is the factor that eliminates passive systems from many implementations. Their mass and energy consumption is very low, and the controlled structure can stay in the safe configuration even in case of power supply failure, which puts them in contrast to many active systems. The mentioned attributes make them a good choice for many structures subjected to vibrations, especially when there is a strong emphasis on maximization of the efficiency/mass ratio of the damping system. Słowa kluczowe: Semiactive damping, Trussframe nodes, PrestressAccumulation Release (PAR), Decentralized control Afiliacje autorów:
 
13.  Hou J.^{♦}, Wang S.^{♦}, Jankowski Ł., Structure damage localization of the slab track by adding virtual masses, WCSCM, 7th World Conference on Structural Control and Monitoring, 20180722/0725, Qingdao (CN), pp.13681373, 2018 Streszczenie: In this paper, a damage localization method based on additional virtual mass and dynamic test of simple harmonic excitation is proposed. Firstly, when additional masses are added to the structure, a large number of virtual structures can be constructed; then the virtual construction formula is derived in order to obtain the dynamic response of virtual structures without adding real mass. After dynamic test of simple harmonic excitation, the dynamic response of virtual structures can be obtained using the acceleration response and virtual construction formula. Furthermore, when the applied harmonic excitation frequency is close to the natural frequency of the structure, the structural response can reach a maximum by adding advisable mass and the mass value can be calculated. When the local structure is damaged, the extreme value and the corresponding position of the additional mass are found by adding mass at different positions in the structure. Thus, the approximate location of the damage is determined according to the results. Finally, the numerical simulation of the elastic foundation beam model simplified by track structure is carried out, and the results show that the damage can be localized. Słowa kluczowe: structural health monitoring, damage identification, slab track, virtual mass Afiliacje autorów:
 
14.  Popławski B., Mikułowski G., Mróz A., Sekuła K.^{♦}, Jankowski Ł., A decentralized strategy of structural reconfiguration in mitigation of vibrations, Procedia Engineering, ISSN: 18777058, DOI: 10.1016/j.proeng.2017.09.363, No.199, pp.16831688, 2017 Streszczenie: This contribution proposes a decentralized closedloop control algorithm for semiactive mitigation of free vibrations in frame structures. The control uses dedicated dissipative devices, which consist of two controllable structural nodes placed pairwise in both ends of selected structural beams. The nodes are capable of a controlled transition between the standard frame mode of operation (full momentbearing ability) and the truss mode in which they do not bear any moments and constitute in fact structural hinges. Synchronous switching is equivalent to reconfiguration of the global structure by (dis)allowing the involved beams to transmit moments and to accumulate vibration energy in the form of their bending strain. Upon switching to the truss mode, the accumulated energy is released into highfrequency local vibrations, which undergo quick dissipation by standard mechanisms of material damping. The approach is illustrated in a numerical example and verified in a preliminary experimental test. Słowa kluczowe: Mitigation of vibrations, Semiactive control, Decentralized control, Structural reconfiguration Afiliacje autorów:
 15p.  
15.  Popławski B., Mikułowski G., Mróz A., Jankowski Ł., Decentralized damping of vibrations in 2D frame structures using controllable nodes, SMART 2017, 8th Conference on Smart Structures and Materials, 20170605/0608, Madrid (ES), pp.94103, 2017 Streszczenie: Extensive research efforts have been recently devoted to semiactive structural control with its paradigms of smart selfadaptivity and low consumption of energy, which is used for local adaptation rather than to generate external control forces. Considered application areas include adaptive landing gears, seismic isolation systems, vehicletrack/span systems, power train electromechanical systems, damping of flexible space structures, vehicle crashworthiness, arctic engineering, wind turbines, etc. A part of the research concerns semiactive management of strain energy for damping of structural vibrations. Early works considered truss structures with stiffnessswitched bars. They later evolved into either standalone one degree of freedom stiffnessswitched dampers and isolators or investigations in triggering modal energy transfer to highlydamped highorder modes. The latter researches seem all to study the fundamental vibration mode of a cantilever beam with two detachable layers and differ mainly in the actuator technologies; the main idea is to employ actuators for a quick release of the vibrationrelated strain energy. This research extends the problem to general 2D frames. Controllable trussframe nodes are incorporated into the structure. Thanks to their controllable ability to transmit moments, they allow for a quick transition between truss and frame modes. We propose a new, decentralized, closedloop control strategy based on local energy measures. Vibration damping is more effective than in the previously studied control scheme based on a global energy measure, especially for higher vibration modes. Mitigation of vibrations will be presented in representative numerical examples, including a comparison to the global energybased control strategy. Finally, results of experimental study, conducted on a structure analogous to the one from numerical simulations, will be demonstrated. Słowa kluczowe: Vibration damping, Smart structures, Semiactive control, PAR strategy, Decentralized damping strategy Afiliacje autorów:
 
16.  Zawidzki M., Jankowski Ł., Szklarski J., Structural optimization of a fiveunit singlebranch TrussZ modular structure, SMART 2017, 8th Conference on Smart Structures and Materials, 20170605/0608, Madrid (ES), pp.525535, 2017 Streszczenie: TrussZ (TZ) is an Extremely Modular System (EMS). Such systems allow for creation of structurally sound freeform structures, are comprised of as few types of modules as possible, and are not constrained by a regular tessellation of space. Their objective is to create spatial structures in given environments connecting given terminals without selfintersections and obstacleintersections. In an EMS, the assembly, reconfiguration and deployment difficulty is moved towards the module, which is relatively complex and whose assembly is not intuitive. As a result, an EMS requires intensive computation for assembling its desired freeform geometrical configuration, while its advantage is the economization of construction and reconfiguration by extreme modularization and mass prefabrication. TZ is a skeletal modular system for creating freeform pedestrian ramps and ramp networks among any number of terminals in space. TZ structures are composed of four variations of a single basic module (TrussZ module, TZM) subjected to affine transformations (mirror reflection and rotation). The previous research on TZ focused on global discrete optimization of the spatial configuration of modules. This contribution reports on the first attempts at structural optimization of the TZM for a singlebranch TZ. Namely, the internal topology of a TZM and sizing of its elements are subject to optimization. An important challenge is due the fact that TZM is to be universal, i.e., it must be designed for the worst case scenario. There are four variations of each module, and due to symmetries there are thus 4^4 = 256 unique 5unit configurations. The structural performance of all of them needs to be evaluated in terms of a typical structural criterion (the maximum von Mises effective stress), and used for structural optimization at the level of a single TZM. Słowa kluczowe: Extremely Modular System, TrussZ, Structural optimization, Effective stress Afiliacje autorów:
 
17.  Faraj R., Popławski B., Suwała G., Jankowski Ł., HolnickiSzulc J., Mitigation of dynamic response in frame structures by means of smart joints, SMART 2017, 8th Conference on Smart Structures and Materials, 20170605/0608, Madrid (ES), pp.138144, 2017 Streszczenie: This paper discusses passive and semiactive techniques of structural control by means of smart joints, and then it proposes a specific smart joints system for frame structures and tests its capability in mitigation of free vibrations. Basically, the proposed solution modifies frame beams by addition of trusstype hinges, and its effectiveness relies on the softening effect that occurs in compression due to geometric nonlinearities and which triggers the highlydamped highfrequency response modes of the structure. First, the finite element (FE) model of the specific frame structure with geometrical nonlinearities is derived, and the proposed passive joints are described and incorporated into the model. Then, their principle of operation and effectiveness is examined numerically for the first two natural modes of vibrations with various initial displacement amplitudes. An objective function is proposed to assess joints placement, based on the efficiency in mitigation of the excited vibrations. Słowa kluczowe: Vibration Damping, Structure Response, Smart Structure, Structural Control Afiliacje autorów:
 
18.  Zawidzki M., Jankowski Ł., Multicriterial optimization of geometrical and structural properties of the basic module of a singlebranch TrussZ structure, WCSMO12, 12th World Congress of Structural and Multidisciplinary Optimisation, 20170605/0609, Braunschweig (DE), pp.19, 2017 Streszczenie: TrussZ (TZ) is an Extremely Modular System (EMS). Such systems allow for creation of structurally sound freeform structures, are comprised of as few types of modules as possible, and are not constrained by a regular tessellation of space. Their objective is to create spatial structures in given environments connecting given terminals without selfintersections and obstacleintersections. In an EMS, the assembly, reconfiguration and deployment difficulty is moved towards the module, which is relatively complex and whose assembly is not intuitive. As a result, an EMS requires intensive computation for assembling its desired freeform geometrical configuration, while its advantage is the economization of construction and reconfiguration by extreme modularization and mass prefabrication. Słowa kluczowe: multicriterial optimization, TrussZ, effective stress, modular systems Afiliacje autorów:
 
19.  Popławski B., Graczykowski C., Jankowski Ł., Controllable TrussFrame Nodes in SemiActive Damping of Vibrations, Advances in Science and Technology, ISSN: 16620356, DOI: 10.4028/www.scientific.net/AST.101.89, Vol.101, pp.8994, 2017 Streszczenie: In recent years, vibration damping strategies based on semiactive management of strain energy have attracted a large interest and were proven highly effective. However, most of published research considers simple one degree of freedom systems or study the same basic example (the first vibration mode of a cantilever beam) with the same control strategy. This contribution focuses on trussframe nodes with controllable momentbearing ability. It proposes and tests an approach that allows the control strategy to be extended to more complex structures and vibration patterns. Słowa kluczowe: adaptive impact absorption, smart structures, semiactive control, safety engineering Afiliacje autorów:
 
20.  Jankowski Ł., Graczykowski C., Pawłowski P., Mikułowski G., Ostrowski M., Popławski B., Faraj R., Suwała G., HolnickiSzulc J., Adaptive SelfProtection against Shock and Vibration, Advances in Science and Technology, ISSN: 16620356, DOI: 10.4028/www.scientific.net/AST.101.133, Vol.101, pp.133142, 2017 Streszczenie: This contribution reviews the challenges in adaptive selfprotection of structures. A proper semiactive control strategy can significantly increase structural ability to absorb impacttype loads and damp the resulting vibrations. Discussed systems constitute a new class of smart structures capable of a realtime identification of loads and vibration patterns, followed by a lowcost optimum absorption of the energy by structural adaptation. Given the always surging quest for safety, such systems have a great potential for practical applications (in landing gears, road barriers, space structures, etc.). Compared to passive systems, their better performance can be attributed to the paradigm of selfadaptivity, which is ubiquitous in nature, but still sparsely applied in structural engineering. Being in the early stages of development, their ultimate success depends on a concerted effort in facing a number of challenges. This contribution discusses some of the important problems, including these of a conceptual, technological, methodological and software engineering nature. Słowa kluczowe: adaptive impact absorption, smart structures, semiactive control, safety engineering Afiliacje autorów:
 
21.  Jankowski Ł., HolnickiSzulc J., Mróz A., A new strategy for adaptive impact absorption (AIA), SMART 2015, 7th ECCOMAS Thematic Conference on Smart Structures and Materials, 20150603/0605, Ponta Delgada (PT), pp.117, 2015 Streszczenie: This contribution presents and overviews a new class of strategies for Adaptive Impact Absorption (AIA) and illustrates a selected strategy in a numerical example. The proposed strategies are based on a challenging approach of a semiactive management and dissipation of structural kinetic and potential energy. The entire process of AIA is considered, including its two main phases: semiactively controlled reception of an impact and semiactively controlled damping of the resulting structural vibrations. Management and redistribution of impact energy seems to be one of the most promising and challenging problems in the field of AIA, which requires a substantial theoretical progress in semiactive control strategies and in structural optimization, besides a technological progress in semiactive actuators. Słowa kluczowe: Adaptive impact absorption, smart structures, adaptive structures, impact energy management, bilinear control, switched systems Afiliacje autorów:
 
22.  Suwała G., Jankowski Ł., Nonparametric identiﬁcation of added masses in frequency domain, 6WCSCM, 6th World Conference on Structural Control and Monitoring, 20140715/0717, Barcelona (ES), pp.23582366, 2014 Streszczenie: This paper presents a frequencydomain, nonparametric method for identification of added masses, and reports on its experimental verification. The identification is directly based on experimentally collected characteristics of the unmodified structure, so that no parametric numerical model of the monitored structure is required. Consequently, there is no need for the initial stage of model updating. This is a continuation of and an improvement over a previous research that resulted in a timedomain identification method, which was tested to be accurate but significantly timeconsuming. For the experimental verification, a 4~m long 3D truss structure with 26 nodes and 70 elements is used. A total of 12 modification cases is tested: in each of 3~selected nodes, 4~additional masses are separately added and successfully identified. Afiliacje autorów:
 
23.  Zhang Q., Jankowski Ł., Duan Z.^{♦}, Structural damage identification using random response based on Virtual Distortion Method, 6WCSCM, 6th World Conference on Structural Control and Monitoring, 20140715/0717, Barcelona (ES), pp.740745, 2014 Streszczenie: Structural damage identification plays a critical role in structural health monitoring on evaluating structural safety and maintaining structural integrity. This paper presents a damage identification approach based on Virtual Distortion Method (VDM) using random response. VDM is a fast structural reanalysis method in which virtual distortions are introduced to simulate structural damages or modifications. Via VDM, responses of damaged structure can be computed quickly without reanalysis of the whole structure. In this paper, firstly the frequency response of damaged structure is constructed efficiently using VDM, and then damage extents are optimized using the objective function which is computed using the MAC (modal assurance criterion) of the power spectrum of theoretical response and measured responses. At last, a plane truss is proposed to verify the proposed method. Afiliacje autorów:
 
24.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Construction of Virtual Structure for Damage Identification, 6WCSCM, 6th World Conference on Structural Control and Monitoring, 20140715/0717, Barcelona (ES), pp.732739, 2014 Streszczenie: This paper presents a damage identification method using virtual structure. The main concept is based on Virtual Distortion method (VDM), which belongs to a fast structural reanalysis method and employs the virtual distortions or virtual forces to simulate the structural modifications. In this paper, the structure with virtual mass, damping or stiffness is defined as virtual structure. Firstly, the frequency response of the virtual structure is constructed by VDM method; Secondly, the natural frequencies of virtual structure with additional masses or stiffness are estimated; At last, the estimated natural frequencies of the virtual structure are used for damage optimization of the structure. A numerical beam model is used to describe and verify the proposed method. Afiliacje autorów:
 
25.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, The substructure isolation method for local analysis at the substructural level, SMART2013, 6th ECCOMAS Thematic Conference on Smart Structures and Materials, 20130903/0906, Turyn (IT), pp.120, 2013 Streszczenie: This paper presents the substructure isolation method, which a novel method for substructural analysis and structural health monitoring (SHM) at the local level. The motivation behind it are the facts that global SHM of large and complex structures is generally difficult and that often only small substructures are crucial and require monitoring. These facts suggest that there is a need for ways of applying global SHM approaches locally, which is impossible with typical substructuring methods. The paper offers an overview of the common substructuring approaches and describes the substructure isolation method. The method splits the task of local monitoring into two stages: (1) Isolation; the outside influences are numerically eliminated from the measured response of the substructure. (2) Local SHM; all methods aimed originally at global SHM can be used with the constructed response of the isolated substructure. Local analysis is possible in time domain as well as in frequency domain; in offline and in online time regimes. The method is illustrated in a numerical example and substantiated in an experimental study using a damaged cantilever beam; the robustness of the isolation with respect to unknown modifications of the outside structure is tested. Słowa kluczowe: Substructuring, Structural Health Monitoring, SHM, Damage identification, Local analysis Afiliacje autorów:
 
26.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Large substructure identification using substructure isolation method, Conference on Sensors and Smart Structures Technologies for Civil, Mechanical, and Aerospace Systems, 20120312/0315, San Diego (US), DOI: 10.1117/12.915102, Vol.8345, pp.83453V17, 2012 Streszczenie: Substructure Isolation Method (SIM) is used for large substructure identification. It utilizes the responses of global structure to construct the responses of the isolated substructure, which is a virtual and independent structure with the same system parameters as the real substructure. Then, the substructure identification is carried out equivalently via the isolated substructure and flexibly by some of the existing identification methods which aim originally at the large structure. Therefore, the performance of the SIM offers the possibility that the large substructure can be identified. A numerical bridge model is used to verify the proposed method, which preforms efficiently and accurately. Słowa kluczowe: Structural Health Monitoring (SHM), Damage identification, Substructure, Interface force Afiliacje autorów:
 10p.  
27.  Zhang Q., Jankowski Ł., Duan Z.^{♦}, Damage identification using Substructural Virtual Distortion Method, Conference on Sensors and Smart Structures Technologies for Civil, Mechanical, and Aerospace Systems, 20120312/0315, San Diego (US), DOI: 10.1117/12.915126, Vol.8345, pp.83453X17, 2012 Streszczenie: This paper presents a Substructure Virtual Distortion Method (SVDM) for damage identification based on Virtual Distortion Method (VDM). VDM is a fast structural reanalysis method by introducing virtual distortions to simulate structural damages. SVDM extends the virtual distortions regard to the damaged elements to the related substructures. Such that the required number of virtual distortions depends on the substructure other than the elements, which reduces the computational work a lot. In addition, for a structure under a certain external force, the dynamic responses may be reflected by a few of main eigenvectors, and thus it only needs to compute the virtual distortions which are relative with these main eigenvectors. This further reduces the computational work. In this paper, first the relation among the virtual distortions of the substructure, actual distortions, and the substructure damage extents are derived; then the main distortions of the substructure are chosen by the contribution analysis of the distortions to the structural responses. In this way, the damages are optimized and identified by minimizing the least square distance between the measured response and the estimated response. A numerical frame model is used to verify the proposed method. Słowa kluczowe: structural health monitoring (SHM), damage identification, Virtual Distortion Method, substructure Afiliacje autorów:
 10p.  
28.  Suwała G., Jankowski Ł., Experimental study of a modelfree method for identification of stiffnessrelated structural damages, EWSHM 2012, 6th European workshop on Structural Health Monitoring, 20120703/0706, Dresden (GE), pp.714721, 2012 Streszczenie: This paper presents a theoretical derivation and an experimental verification of a modelfree method for identification of stiffnessrelated damages. The proposed method requires no parametric numerical model of the monitored structure, which obviates the need for initial model updating and fine tuning. The paper introduces the general methodology, including the inverse problem, focuses it on stiffnessrelated damages, and reports on an experimental verification. A 4meterlong, 70element truss steel structure made of a commercially available system of nodes and connecting tubes is used for that purpose. Damage is simulated by an intentional replacement of a structural element. Afiliacje autorów:
 
29.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Substructure Isolation Method for online local damage identification using time series, EWSHM 2012, 6th European workshop on Structural Health Monitoring, 20120703/0706, Dresden (GE), pp.16311638, 2012 Streszczenie: This paper proposes a Substructure Isolation Method based on time series (SIMTM) of measured local response and intended for local online monitoring of substructures. The method consists of two key steps: (numerical) construction of the isolated substructure, and local identification. The isolated substructure is an independent virtual structure, which is separated from the global structure with virtual supports placed in their interface. In the first step, the response of the isolated substructure is constructed by linear combinations of subtime series of the measured local responses. Then, natural frequencies of the isolated substructure are identified based on the constructed response and used for local identification. The method has no requirements on the initial state of the structure. The isolation can be carried out time section by time section using the successive fragments of the measured responses, so that the approach can be used for online monitoring. A numerical frame model is used to verify the proposed online monitoring method. Afiliacje autorów:
 
30.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Local damage identification in frequency domain based on substructure isolation method, ANCRiSST2011, 6th International Workshop on Advanced Smart Materials and Smart Structures Technology, 20110725/0726, Dalian (CN), pp.19, 2011 Streszczenie: This paper proposed a frequency domain method of substructure identification for local health monitoring. The substructure isolation method (SIM) consists of two steps: the first is the construction of isolated substructure which is the key of the method, and the second is damage identification of substructure. The isolated substructure is a virtual and independent structure, and it have the same physical parameters of the real substructure with the additional virtual supports on boundary, which is realized by operating the measured response. This paper extends the SIM method to frequency domain, which could make the method employ more measured response and compute more efficiently. A massspring numerical model is used to verify the theory of the SIM method, and a cantilever beam is experimented to test the method. The method preformed efficiently and accurately in the both numerical model and experiment. Afiliacje autorów:
 
31.  Qingxia Z.^{♦}, Jankowski Ł., Zhongdong D.^{♦}, Experimental verification of a methodology for simultaneous identification of coexistent loads and damages, CM/MFPT 2011, 8th International Conference on Condition Monitoring and Machinery Failure Prevention Technologies, 20110620/0622, Cardiff (GB), pp.112, 2011 Streszczenie: This paper presents the concept of smart structures dedicated to improving structural safety in case of unpredictable impact loadings. The concept is developed by bringing together two different ideas: adaptive impact absorption (AIA) and structural health monitoring (SHM). The potential for safe energy dissipation is maximized by optimum structural adaptation to impact loading parameters, for which the AIA subsystem is responsible. The SHM subsystem is used for online identification of impact type loadings, which is necessary in order to trigger optimum adaptation, as well as for postimpact damage assessment. Both subsystems depend on smart material technologies: optimum adaptation can be implemented through a small number of optimally distributed structural fuses, that is elements with controllable yield stresses, which can be implemented using magnetorheological fluids, while the health and loading monitoring require a reliable sensing system, e.g. based on piezomaterials. The paper presents the general concept, provides a literature review and discusses in detail the challenges related to the SHM part. Afiliacje autorów:
 
32.  HolnickiSzulc J., Jankowski Ł., Smart technologies for structural safety, CMM 2011, 19th International Conference on Computer Methods in Mechanics, 20110509/0512, Warszawa (PL), pp.05717, 2011 Streszczenie: This paper presents the concept of smart structures dedicated to improving structural safety in case of unpredictable impact loadings. The concept is developed by bringing together two different ideas: adaptive impact absorption (AIA) and structural health monitoring (SHM). The potential for safe energy dissipation is maximized by optimum structural adaptation to impact loading parameters, for which the AIA subsystem is responsible. The SHM subsystem is used for online identification of impact type loadings, which is necessary in order to trigger optimum adaptation, as well as for postimpact damage assessment. Both subsystems depend on smart material technologies: optimum adaptation can be implemented through a small number of optimally distributed structural fuses, that is elements with controllable yield stresses, which can be implemented using magnetorheological fluids, while the health and loading monitoring require a reliable sensing system, e.g. based on piezomaterials. The paper presents the general concept, provides a literature review and discusses in detail the challenges related to the SHM part. Słowa kluczowe: adaptivity, crashworthiness, inverse problems, structural monitoring, smart materials Afiliacje autorów:
 
33.  Szolc T., Jankowski Ł., Pochanke A.^{♦}, Michajłow M., Vibration control of the coal pulverizer geared drive system using linear actuators with the magnetorheological fluid, SIRM 2011, 9th International Conference on Vibrations in Rotating Machines, 20110221/0223, Darmstadt (GE), pp.110, 2011 Streszczenie: Torsional vibrations are in general rather troublesome to control from the viewpoint of proper control torque generation as well as because of difficulties of imposing the control torques on quickly rotating parts of the drive or rotorshaft systems. In this paper there is proposed an active control technique based on the linear actuators with the magnetorheological fluid (MRF) connecting the drive system planetary gear housing with the immovable rigid support. Here, by means of the magnetorheological fluid of adjustable viscosity control damping torques are generated. Such actuators can effectively suppress amplitudes of severe transient and steadystate rotational fluctuations of the gear housing position and in this way they are able to minimize dangerous oscillations of dynamic torques transmitted by successive shaft segments in the entire drive system. The general purpose of the considerations is to control torsional vibrations of the powerstation coalpulverizer drive system driven by means of the asynchronous motor and the single stage planetary gear. In the computational examples drive system transient torsional vibrations induced by the electromagnetic motor torques during startups as well as steadystate vibrations excited by the variable dynamic retarding torques generated by the coal pulverizer during nominal operation have been significantly attenuated. Słowa kluczowe: Torsional vibrations, rotational fluctuation, magnetorheological fluid Afiliacje autorów:
 
34.  Suwała G., Jankowski Ł., A benchmark for identification of structural modifications and inelastic impacts: the structure, test data and an example solution, SMART2011, 5th ECCOMAS Thematic Conference on Smart Structures and Materials, 20110706/0708, Saarbrücken (DE), pp.111, 2011 Streszczenie: This paper proposes a simple labsize benchmark for testing algorithms in two identification problems related to global structural health monitoring (SHM): identification of structural modifications and identification of inelastic impacts. A 3D trusslike structure, constructed of a commercial tube/node system, is used. Structural modifications are implemented by attaching additional nodal masses or by cutting a selected element to reduce its stiffness. Inelastic impact is simulated by an impulsive excitation of an additional nodal mass. Technical specification and experimental characteristics of the unmodified structure are provided for model updating. Several modification and impact cases are experimentally tested. All the data and measurements are freely accessible in Internet. An evaluation system is proposed for assessing the solutions, based on identification accuracy, instrumentation and source lines of code. The authors encourage the readers to test their approaches on the provided data. With each solution received, the evaluations will be calculated and published online. Afiliacje autorów:
 
35.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Substructural damage identification using time series of local measured response, 5WCSCM 2010, 5th World Conference on Structural Control and Monitoring, 20100712/0714, Tokyo (JP), pp.110, 2010 Streszczenie: This paper presents a Substructure Isolation method for substructural damage identification using time series of local measured response. Isolated Substructure is a virtual and independent structure which is numerically separated from the global structure by adding virtual supports on the substructure interface. The basic concept of the isolation method is that: first time series of substructural responses are divided into several subseries with overlap; through the linear combination of all the subseries, when the boundary response are constrained to zeros, the corresponding inner responses are the constructed responses of the Isolated Substructure; then the substructural damage identification can be performed equivalently by the modes of the Isolated Substructure which are identified from the constructed inner responses. Numerical model of a sixspan truss and an experiment of a cantilever beam are used to validate the method. Both the isolation and damage identification are preformed very well using local measured responses. Afiliacje autorów:
 
36.  Mróz M.^{♦}, Jankowski Ł., HolnickiSzulc J., VDMbased identification of localized, damage induced damping, EWSHM 2010, 5th European workshop on Structural Health Monitoring, 20100629/0702, Sorrento (IT), pp.988993, 2010 Streszczenie: This paper presents and experimentally verifies a method for identification of structural damage. The work is focused on such damage types as cracks, delamination or excessive allowances, which may not cause significant stiffness degradation but induce noticeable additional damping. Damaged elements are located and the damage is assessed in terms of the damageinduced damping and also the stiffness degradation. The Virtual Distortion Method (VDM) is used for modeling of the modifications. Afiliacje autorów:
 
37.  Suwała G., Jankowski Ł., Modelfree damage identification of skeletal structures, EWSHM 2010, 5th European workshop on Structural Health Monitoring, 20100629/0702, Sorrento (IT), pp.925930, 2010 Streszczenie: This paper presents and verifies experimentally a modelfree methodology for offline damage identification of truss structures. The Virtual Distortion Method (VDM) is used, which allows the approach to be based entirely on experimentally obtained nonparametric characteristics of the monitored structure, so that no parametric numerical modeling is necessary. The damage is modeled using certain damageequivalent pseudoloads, which are convolved with experimentally obtained local responses of the original structure to compute the response of the damaged structure. An effective sensitivity analysis is possible via the adjoint variable method. Afiliacje autorów:
 
38.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Substructure isolation and identification using FFT of measured local responses, EWSHM 2010, 5th European workshop on Structural Health Monitoring, 20100629/0702, Sorrento (IT), pp.913918, 2010 Streszczenie: A substructuring method is presented for substructure identification and local health monitoring. The concerned substructure is numerically separated from the global structure to be a socalled Isolated Substructure by adding virtual supports on the substructure interface. The isolated substructure is a small and independent structure; its virtual supports are constructed using the FFT of measured local responses of the global structure. The damage of the substructure can be then identified easily by any of the classical methods which perform well on global structures. An experiment of a cantilever beam, of which the upper part is chosen as the substructure, is used to validate the method. Afiliacje autorów:
 
39.  Zhang Q., Jankowski Ł., Duan Z.^{♦}, Fast identification of loads and damages using a limited number of sensors, EWSHM 2010, 5th European workshop on Structural Health Monitoring, 20100629/0702, Sorrento (IT), pp.10391044, 2010 Streszczenie: This paper presents a method for fast identification of coexistent loads and damages, in which the number of sensors is mainly decided by the number of unknown loads.The computational efficiency is improved by Virtual Distortion Method (VDM), with which the repeated estimation of system impulse response is performed efficiently and by a local interpolation of perturbations of the structural response with respect to damage parameters. The proposed methodology is verified by a numerical example of a multispan frame. Afiliacje autorów:
 
40.  Szolc T., Jankowski Ł., Pochanke A.^{♦}, Magdziak A.^{♦}, An application of the magnetorheological actuators to torsional vibration control of the rotating electromechanical systems, IFToMM, 8th International Conference on Rotor Dynamics, 20100912/0915, Seoul (KR), pp.488495, 2010 Streszczenie: In the paper control of transient and steadystate torsional vibrations of the driven by the asynchronous motor laboratory drive system of the imitated coal pulverizer is performed by means of actuators with the magnetorheological fluid. The main purpose of these studies is a minimisation of vibration amplitudes in order to increase the fatigue durability of the most responsible elements. The theoretical investigations are based on a hybrid and finite element structural model of the vibrating mechanical system as well as on sensitivity analysis of the response with respect to the actuator damping characteristics. For suppression of transient torsional vibrations excited by electromagnetic torques generated by the motor and by the coal pulverizer tool there is proposed a control strategy based on actuators in the form of rotary control dampers. Słowa kluczowe: Semiactive control, torsional vibrations, electromechanical drive system, control dampers, magnetorheological fluid Afiliacje autorów:
 
41.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Substructural damage identification using Local Primary Frequency, ISSE11, 11th International Symposium on Structural Engineering, 20101218/1220, Guangzhou (CN), pp.16, 2010 Streszczenie: This paper presents a substructuring method on damage identification using Local Primary Frequency (LPF).When a local excitation is applied on a concerned substructure, if the caused vibration mainly consists of only one single modal which represents most of the substructural distortion, then the corresponding frequency is defined as the substructural LPF. LPF reflects more information of the substructure and hence is more sensitivity to the substructural damage. Therefore, LPF can be used for substructural model updating and identification. However, generally substructures don’t own LPF. In this case, virtual supports constructed by Substructure Isolation Method are applied on the substructural boundary, such that it can enhance the constraint on the boundary, and decrease the influence from elements outside the substructure. In this way, the substructure sensitivity is enhanced and correspondingly the LPF of the substructure can be constructed. Numerical simulation of a threestory space frame structure testifies that substructural damages are identified effectively by this method. Słowa kluczowe: Structure Health Monitoring (SHM), Damage Identification, substructuring method, Substructure Isolation Method, Local Primary Frequency (LPF), Virtual Supports Afiliacje autorów:
 
42.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Substructure isolation for local structural health monitoring, ECCOMAS Thematic Conference: International Symposium on Inverse Problems in Mechanics of Structures and Materials, 20090423/0425, Łańcut (PL), pp.3334, 2009 Streszczenie: This paper describes an effective method of substructure isolation for local structural health monitoring (SHM). In practice, often only a small part of a larger structure is critical and needs monitoring [1]. However, typical SHM methods require modeling or analysis of the global structure, which can be costly, timeconsuming and errorprone. The proposed approach is based on the virtual distortion method [2]; the substructure is isolated from the entire structure by placing modeled fixed supports in all nodes of their mutual boundary. Therefore, given an excitation of the substructure and a measured response, the response of the substructure treated as fixed supported can be computed. Only experimental data are used for isolation, and no numerical modeling is required. A numerical experiment of damage identification in a frametruss will be presented during the talk to validate the methodology at 5% rms measurement error level. It is omitted here due to space constraints. Afiliacje autorów:
 
43.  Mróz M.^{♦}, Jankowski Ł., HolnickiSzulc J., A VDMbased method for fast reanalysis and identification of structural damping, WCSMO8, 8th World Congress on Structural and Multidisciplinary Optimization, 20090601/0605, Lisbon (PT), pp.19, 2009 Streszczenie: This paper proposes a new approach for modeling and identification of damping in linear structures. The approach is based on the Virtual Distortion Method (VDM), which is a reanalysis methodology for fast modeling and identification of structural parameters. The VDM is extended in the sense of considering structural damping in frequency domain. The assumed damping model is a modified version of the proportional damping, which allows to distinguish between and to modify independently the damping properties of each element and in each degree of freedom. In this way, a precise formulation of the task of remodeling of damping is possible. Moreover, the proposed approach is used to state and solve the (basically nonlinear) inverse problem of identification of material damping by decomposing it into two linear subproblems. Słowa kluczowe: damping identification, structural reanalysis, Virtual Distortion Method (VDM) Afiliacje autorów:
 
44.  Zhang Q., Jankowski Ł., Duan Z.^{♦}, Simultaneous identification of moving mass and structural damage, WCSMO8, 8th World Congress on Structural and Multidisciplinary Optimization, 20090601/0605, Lisbon (PT), pp.110, 2009 Streszczenie: Identification of damage and moving load (or mass) are crucial problems in structural health monitoring (SHM). However, it seems there is not much investigation on simultaneous identification of the two factors, although in practice they usually exist together. This paper proposes a methodology to solve the coupled problem based on the Virtual Distortion Method (VDM): the damaged structure is modeled by an equivalent intact structure (called the distorted structure) subjected to the same moving mass (or in fact to the equivalent responsecoupled moving load) and to certain virtual distortions which model the damage. The measured structural response is used to identify the moving mass and the damage; unknown mass and damage extents are used as the optimization variables instead of the usually chosen moving massequivalent force. In this way wellconditioning of the identification is ensured and the number of the necessary sensors is decreased. The numerical costs are considerably reduced by using the introduced concept of the moving dynamic influence matrix. The proposed identification method can be used both offline and online by a repetitive application in a moving time window. A numerical experiment of a beam with 5% measurement error demonstrates that the moving masses can be identified along with the damage extents. Słowa kluczowe: Structural health monitoring (SHM), Moving mass (load) identification, Damage identification, Virtual distortion method (VDM) Afiliacje autorów:
 
45.  Suwała G., Jankowski Ł., Modelfree identification of added mass, WCSMO8, 8th World Congress on Structural and Multidisciplinary Optimization, 20090601/0605, Lisbon (PT), pp.110, 2009 Streszczenie: This paper presents and experimentally validates a modelfree methodology for offline identification of modifications of structural mass. The proposed approach makes use of the Virtual Distortion Method (VDM) and is based entirely on experimentally measured data of the original unmodified structure, which is a significant advantage: no numerical modeling of the structure and tedious updating of the model are necessary. The mass modification is modeled using equivalent virtual distortion forces and experimentally obtained local impulseresponses of the unmodified structure. The identification amounts to solving an optimization problem of minimizing the meansquare distance between measured and modeled responses of the modified structure; a quick first and secondorder sensitivity analysis using the adjoint variable method is proposed. The method is validated experimentally using a 4meterlong 70element truss structure. Słowa kluczowe: mass identification, modelfree SHM, virtual distortion method (VDM), adjoint variable method Afiliacje autorów:
 
46.  Kołakowski P., Jankowski Ł., Świercz A., Wikło M., Timedomain identification of damage in skeletal structures using strain measurements and gradientbased optimization, ISMA 2008, International Conference on Noise and Vibration Engineering, 20080915/0917, Louvain (BE), pp.32573266, 2008 Streszczenie: This paper presents an improved numerical tool for identification of damage in skeletal structures. The problem of identification has been formulated in the time domain within the framework of the Virtual Distortion Method (VDM). VDM generally belongs to fast structural reanalysis methods and can be applied to Structural Health Monitoring problems, among others. The major computational asset of VDM is the influence matrix, containing all the localglobal interrelations for a structure due to given perturbations e.g. initial strain or external force. A nonlinear least squares problem with strains, entering the objective function, is the subject of consideration. Strains are used in order to have relatively smooth variations (compared to accelerations) of the analyzed signal in time. The change of stiffness is the design variable. Analytical gradients are implemented in the optimization code based on the LevenbergMarquardt algorithm with some penalty function terms. The efficiency of the software tool is demonstrated for a numerical example of a 2D truss structure. A breakthrough in terms of computational time reduction has been observed compared to the previously used steepestdescent optimization. The presented software assumes the feasibility of reliable measurements of strains in time for real skeletal structures (e.g. truss bridges). Future research will include experimental verification of the idea with piezoelectric sensors acting as tensometers. Afiliacje autorów:
 
47.  Zhang Q., Jankowski Ł., Duan Z.^{♦}, Identification of coexistent load and damage based on virtual distortion method, EWSHM 2008, 4th European workshop on Structural Health Monitoring, 20080702/0704, Kraków (PL), pp.11241131, 2008 Streszczenie: This paper presents a novel method to identify coexistent load and damage based on the idea of Virtual Distortion Method (VDM), which is significant for structural healthy monitoring. This method models a system with unknown damage and load by an equivalent undamaged system with the same load and certain virtual distortions, which are estimated stepwise via measured response. Then damage size can be computed by the estimated virtual distortions. It could be used for both offline and online identification. A numerical experiment validates that two kinds of damage sizes can be identified as well as coexistent continuous and triangular loads. Moreover two methods (load shape function and initial system iterates) are proposed and incorporated to improve the computational accuracy and to reduce the numerical effort. Afiliacje autorów:
 
48.  Suwała G., Jankowski Ł., Modelless impact mass identification, EWSHM 2008, 4th European workshop on Structural Health Monitoring, 20080702/0704, Kraków (PL), pp.374381, 2008 Streszczenie: This paper proposes a new modelless method for offline identification of a mass impacting an elastic structure. The method is aimed at the identification of both mass and its velocity, makes use of the Virtual Distortion Method (VDM) and assumes the inelastic impact case, i.e. permanent modification of structural properties. Since the proposed approach is completely based on experimentally measured data, no numerical modeling and tedious finetuning of the model are necessary. The impacting mass is modeled using virtual distortion forces and an experimentally obtained system transfer matrix. The identification amounts to solving an optimization problem of minimizing the meansquare distance between measured and modeled structural responses, the latter is based on previously recorded responses of the unaffected structure. Afiliacje autorów:

Abstrakty konferencyjne
1.  Pisarski D., Jankowski Ł., Distributed control of modular structures based on the identification of the interaction forces, IPM 2019, 5th International Conference on Inverse Problems Methods, 20190522/0524, Kombornia (PL), pp.4344, 2019 Streszczenie: In the present work, we propose a distributed collaborative controller to stabilize the vibration of modular systems. The method relies on the partitioning the structure, in a way that leads to a set of dynamically interconnected subsystems, each operated with an individual subcontroller. The key novelty in the proposed approach lies in the introduction of a collaboration between the neighboring subcontrollers. This collaboration is realized by exchanging some of the state information, allowing the establishment of shortterm predictions of the interaction forces, identifying the boundary conditions for the subsystems. For the predictions, we employ autoregressive linear dynamical models which preserve the linear representation of the subsystems' dynamics. This allows, for each of the subsystems, defining and solving the problem of optimal stabilization based on the LQR method. The proposed method is examined for an actively controlled cantilever structure equipped with electromagnetic actuators. The performance of the designed controller is tested by comparing it to the optimal controller established by the solution to the centralized LQR problem. In addition, the distributed controller is compared to the decentralized case, where we assume a set of local independent subcontrollers. The computational complexity of the distributed control method is analyzed for different settings in the modeling of the predictions of the interaction forces. Afiliacje autorów:
 
2.  Gawlicki M., Jankowski Ł., Identification of a moving load 2D path under insufficient instrumentation, IPM 2019, 5th International Conference on Inverse Problems Methods, 20190522/0524, Kombornia (PL), pp.12, 2019 Streszczenie: This contribution is devoted to the problem of indirect identification of 2D trajectories of moving loads based on the measured mechanical responses of the loaded structure. This is an inverse problem of load identification, and such problems have been intensively studied. Such problems are typically characterized by (1) a very large number of structural degrees of freedom that can be excited by the moving load and (2) a limited number of sensors that are used to measure the response. In effect, the na¨ıve formulation based on minimization of the residuum norm is underdetermined, and the corresponding identification problem has an infinite number of exact solutions. Thus, in order to guarantee the uniqueness of the solution, the generality of the load is typically limited by assuming that the trajectory of the moving load is known (most often, the problem is reduced to the case of a single vehicle moving over a 1D bridge at a constant velocity) and that only the magnitude of the load is subject to identification. In contrast, our aim here is to identify more general loads, and in particular trajectories of loads that are freely moving on 2D structures like plates. Słowa kluczowe: moving load identification, inverse problem, trajectory identification Afiliacje autorów:
 
3.  Błachowski B., Tauzowski P., Świercz A., Jankowski Ł., Sensor placement for structural damage identification by means of topology optimization, PCMCMM, 4th Polish Congress of Mechanics, 23rd International Conference on Computer Methods in Mechanics, 20190908/0912, Kraków (PL), pp.1, 2019 Streszczenie: Damage identification attracted a lot of attention during the last three decades. The reason for that is the fact that large number of existing civil infrastructures reached their service life and growing number of structures is equipped with Structural Health Monitoring (SHM) systems. A successful structural damage identification is determined by three inseparably coupled factors: sensor placement, damage location and its extend, and finally location and timefrequency characteristics of the applied excitation. The purpose of this study is to address the first of the mentioned aspects, namely optimal sensor placement. A vast literature has been devoted to optimal sensor placement methods among which Effective Independence (EI) method proposed by Kammer and Tinker is one of the most successfully applied in practice. However, EI method is dedicated rather to testanalysis correlation and therefore more specific methods for damage identification are still needed. Additionally, in the case of large civil structures, which are intended to be equipped with large amount of sensors of different type, other sensor placement methods can be more efficient. Recently, a promising idea of utilizing a topology optimization approach for the purpose of sensor placement has been proposed by Bruggi and Mariani. The goal of this study is to extend their method, which has been verified on a plate structure, to the case of a FE model of a real arch bridge structure consisting a few thousands degrees of freedom. The main purpose of this work is to find the optimal arrangement of sensors on the structure to detect defects most accurately. The objective function for the problem formulated in this way is the total, weighted difference between the deformation of a damaged and undamaged state. This problem is very similar to the topological optimization, where we search for the optimal material distribution minimizing the mass of the structure while meeting the conditions related to some mechanical properties such as the maximum displacement of the structure, stress intensity or load capacity. This similarity led us to apply topological optimization to the problem of optimal placement of damage sensors. Several numerical examples prove the applicability of topological optimization for optimal sensor placement problem. Słowa kluczowe: Sensor Placement, Damage Identification, Topology Optimization Afiliacje autorów:
 
4.  Rustighi E.^{♦}, Jankowski Ł., Prediction of acoustic emission of a rigid electrodes DEAP loudspeaker, RASD, 13th International Conference on Recent Advances in Structural Dynamics, 20190415/0417, Lyon, France (FR), pp.14, 2019 Streszczenie: Dielectric ElectroActive Polymers (DEAPs) are lightweight materials whose dimensions change significantly when subjected to electric stimulation. One form of DEAP construction consists of a thin layer of dielectric sandwiched between two perforated rigid electrodes. They can be used as an actuator or a sensor and have the potential to be an effective replacement for many conventional transducers. This paper refers to their use as loudspeakers. To date, at DEAP loudspeakers have been prototyped and tested but no numerical prediction of their acoustic perfomances has been presented. In this paper an elemental model is presented, where the electrodes are modelled as bending plates, the dielectric as a Winkler bedding and the acoustic impedance calculated assuming baffled conditions. The impedances of the elements are stacked together and preliminary results are shown. Afiliacje autorów:
 
5.  Ostrowski M., Blachowski B., Jankowski Ł., Pisarski D., SemiActive Control of Mechanical Energy Transfer Between Vibrational Modes, SolMech 2018, 41st SOLID MECHANICS CONFERENCE, 20180827/0831, Warszawa (PL), No.P136, pp.408409, 2018 Streszczenie: The vibration attenuation problem has been solved using many different methods, some of which involve the use of advanced control algorithms. The topic of harvesting the energy of structural vibrations is less explored. For that reason, this contribution studies the problem of conversion of mechanical energy of vibrations. The paper presents a method of semiactive control, which is applied to dynamically transfer the vibration energy into a selected vibration mode. The target mode is selected in such a way that the amount of energy that can be recovered during the vibration process is maximized. In other words, switching between two modes is not intended to dissipate the energy of vibrations, but rather to maximize the energyharvesting potential of the overall system. The concept will be illustrated using an example of a simple frame structure, in which semiactively controlled lockable joints modify the modal properties of the structure. Słowa kluczowe: semiactive control, lockable joints, energyharvesting Afiliacje autorów:
 
6.  Popławski B., Mikułowski G., Wiszowaty R., Jankowski Ł., Semiactive mitigation of externally induced vibrations, SolMech 2018, 41st SOLID MECHANICS CONFERENCE, 20180827/0831, Warszawa (PL), No.P197, pp.12, 2018 Streszczenie: Almost all manmade structures are exposed to vibration. Regardless of whether these are large structures such as bridges or skyscrapers, machines with rotating parts such as engine shafts, frame structures or vehicle suspensions, excessive vibrations can be very harmful. From the perspective of their effects they can be seen as very spectacular (e.g., a collapse of a bridge) or not worth much attention (e.g., a failure of a motor shaft), but in each of these cases, the effect is the destruction of the structure and a negative impact on the users of these devices. Afiliacje autorów:
 
7.  Gawlicki M., Jankowski Ł., Identification of a load moving on a plate using the l1 norm minimization, SolMech 2018, 41st SOLID MECHANICS CONFERENCE, 20180827/0831, Warszawa (PL), No.P226, pp.12, 2018 Streszczenie: There are two fundamental inverse problems in the field of structural health monitoring (SHM): identification of damages and identification of loads. Effectiveness of the related computational methods is crucial for maintaining integrity of the monitored structures. This contribution considers identification of unknown loads based on measurements of structural response. It is a relatively extensively researched problem: reviews of techniques used for offline load identification can be found in [1,2], while techniques for online identification are reviewed in [3]. Afiliacje autorów:
 
8.  Gawlicki M., Jankowski Ł., Identification of moving loads using the l1 norm minimization, CMM 2017, 22nd International Conference on Computer Methods in Mechanics, 20170913/0916, Lublin (PL), pp.12, 2017 Streszczenie: This contribution deals with the inverse problem of indirect identification of moving loads. The identification is performed based on the recorded response of the loaded structure and its numerical model. A specific feature of such problems is a very large number of the degrees of freedom (DOFs) that can be excited and a limited number of available sensors. As a result, unless the solution space is significantly limited, the identification problem is underdetermined: it has an infinite number of exact, observationally indistinguishable solutions. We propose an approach based on the assumption of sparsity of the excitation, which can be expressed in the form of a requirement of a bounded l1 norm of the solution. As long as the loads are sparse, the approach allows them to be freely moving, without the usual assumption of a constant velocity. We test the approach in a numerical example with 10% rms measurement noise and describe an experimental setup that is being prepared to perform experimental verification. Słowa kluczowe: inverse problems, structural mechanics, moving load identification, sparsity, l1 norm Afiliacje autorów:
 
9.  Gawlicki M., Jankowski Ł., Identification of moving loads via l1constrained solutions, ECCOMAS  IPM 2017, 4th International Conference on Inverse Problems in Mechanics of Structures and Materials, 20170531/0602, Rzeszów  Krasiczyn (PL), pp.2526, 2017 Streszczenie: Indirect identification of moving loads based on the measured response is one of the crucial problems in structural health monitoring. It is important in automated assessment of structures and pavements, in traffic monitoring and control, and as a prerequisite for structural control. As such, it has been intensively researched. An important difficulty is that a moving load can excite a very large number of structural Dofs, which all have to be taken into account in the identification procedure based on measurements of a much more limited number of sensors. A straightforward formulation yields thus an underdetermined problem with an infinite number of solutions. Therefore, in most of the approaches so far, the solution space is significantly limited by the assumption that the load corresponds to a single vehicle moving at a constant velocity, which excludes loads of a more general nature (e.g., multiple loads). However, instead of limiting the solution space, it can be noted that in practice moving loads are sparse in time and space, which fits the framework of compressed sensing. Such an a priori knowledge of sparsity is typically expressed by limiting the l1 norm of the solution. To our knowledge, although used in other contexts, the concept has not been applied so far for identification of moving loads. The approach is tested in a numerical example with 10% rms measurement noise. Experimental work is in progress. Afiliacje autorów:
 
10.  Popławski B., Mikułowski G., Mróz A.^{♦}, Sekuła K.^{♦}, Jankowski Ł., A decentralized strategy of structural reconfiguration in mitigation of vibrations, EURODYN 2017, X International Conference on Structural Dynamics, 20170910/0913, Rome (IT), pp.114, 2017  
11.  Popławski B., Mikułowski G., Jankowski Ł., Semiactive damping of forced vibrations utilizing controllable trussframe nodes, ICAST2017, The 28th International Conference on Adaptive Structures and Technologies, 20171008/1011, Kraków (PL), pp.1, 2017  
12.  Zieliński T.G., Jankowski Ł., Opiela K., Deckers E.^{♦}, Modelling of poroelastic media with localised mass inclusions, SAPEM'2017, SAPEM'2017  5th Symposium on the Acoustics of PoroElastic Materials, 20171206/1208, Le Mans (FR), pp.12, 2017  
13.  Popławski B., Mikułowski G., Jankowski Ł., Onoff damping of free vibrations and optimum actuator placement, SolMech 2016, 40th Solid Mechanics Conference, 20160829/0902, Warszawa (PL), pp.12, 2016  
14.  Hou J.^{♦}, Su L.^{♦}, Jankowski Ł., Cable force identification based on substructure isolation method, Structures16, The 2016 Structures Congress, 20160828/0901, Jeju Island (KR), pp.16, 2016 Streszczenie: Aiming at this characteristic that the cable force identification precision is influenced by factors such as stiffness, boundary conditions and length, especially when the length of cable is short, boundary conditions cannot be simplified as fixed or pinned directly. Therefore, the method of adding virtual supports on the structure was proposed for cable force identification. The method of adding virtual supports on cable is based on the Substructure Isolation, through the change rule of natural frequency realize the structure damage identification. The virtual supports were constructed by the Substructure Isolation method using the liner combination of responses. By adding virtual supports realized that the substructures of cable were constructed, using the method can be additional virtual support in different position of the cable and get more virtual structures, combined with the frequency variation law of all virtual structures, the damage identification of cable can be carried out quickly and accurately. Afiliacje autorów:
 
15.  HolnickiSzulc J., Jankowski Ł., Mróz A., Mitigation of impactborn vibrations, Euromech Colloquium [562] – Stability and Control of Nonlinear Vibrating Systems, 20150524/0528, Sperlonga (IT), pp.2829, 2015  
16.  HolnickiSzulc J., Faraj R., Graczykowski C., Jankowski Ł., Mikułowski G., Mróz A., Ostrowski M., Pawłowski P., Wiszowaty R., Adaptive impact absorption  potential applications for safety engineering, SMART 2015, 7th ECCOMAS Thematic Conference on Smart Structures and Materials, 20150603/0605, Ponta Delgada (PT), pp.12, 2015 Słowa kluczowe: Smart And Adaptive Structures, Adaptive Impact Absorption, Safety Engineering Afiliacje autorów:
 
17.  Suwała G., Jankowski Ł., Effective numerical techniques for identification of structural mass modifications, TKI 2014, XIII Konferencja NaukowoTechniczna, 20140506/0509, Licheń Stary k. Konina (PL), pp.12, 2014 Streszczenie: This contribution focuses on effective numerical techniques used in a nonparametric method for identification of structural mass modifications. The approach utilizes the Virtual Distortion Method (VDM), which allows experimentally measured data to be directly used in the modeling process. As a result, experimentally obtained characteristics of the involved structure are used directly, so that no parametric modeling and timeconsuming finetuning of the parameters are necessary. On the other hand, there are significant computational costs related to the need of direct processing of the measured time series, which require effective numerical techniques. Mass identification is formulated as an optimization problem of minimizing the mean square distance between the measured and the computed structural responses, where the optimization variables are massrelated parameters. Given the testing excitation (which can be unknown but should be reproducible) and the measured response of the original undamaged structure, the corresponding response of the structural mass modifications is computed by using certain massequivalent pseudo loads, which are convolved with experimentally obtained local impulse responses of the unaffected structure. The methodology is validated numerically and experimentally using a 4meterlong, 70element truss. Słowa kluczowe: mass identification, virtual distortion method (VDM), conjugate gradient least squares, FFT, nonparametric Afiliacje autorów:
 
18.  HolnickiSzulc J., Jankowski Ł., VDM in inverse problems of safety engineering, IPM 2013, ECCOMAS Thematic Conference: International Conference IPM 2013 on Inverse Problems in Mechanics of Structures and Materials, 20130424/0427, Baranów Sandomierski (PL), pp.2122, 2013 Streszczenie: The virtual distortion method (VDM) [1] is a quick reanalysis method developed in the Institute of Fundamental Technological Research (IPPT PAN). Earlier related work includes the research of professors Nowacki, Eshelby, Kroener, Argyris, Maier, Majid and Celik, and others; for references see [1, 2]. The term virtual distrotion has been coined in 1989 [3], and the concept of the influence matrix has been proposed, which is the distinguishing factor of the VDM that provides for its effectiveness. This contribution presents the background and formulation of the method and reviews its applications in safety engineering. Afiliacje autorów:
 
19.  Suwała G., Jankowski Ł., Modelfree monitoring of structures, IPM 2013, ECCOMAS Thematic Conference: International Conference IPM 2013 on Inverse Problems in Mechanics of Structures and Materials, 20130424/0427, Baranów Sandomierski (PL), pp.6162, 2013 Streszczenie: This contribution presents the modelfree approach to structural identification and monitoring, which has recently been developed in IPPT PAN [1–3]. The approach adapts the essentially nonparametric methodology of the virtual distortion method (VDM, [4]). Monitored structure is characterized in a purely experimental way, so that no parametric numerical modelling is required: the monitoring process is based directly on experimentally measured local impulse response functions. Even though, the approach can be used for identification of parametrized modifications of mass and stiffness or inelastic impacts. In comparison to other monitoring methods, it is characteristic enough to warrant the name of a modelfree approach. Afiliacje autorów:
 
20.  Hou J.^{♦}, Jankowski Ł., Ou J.^{♦}, Online local structural health monitoring using the substructure isolation method, SolMech 2012, 38th Solid Mechanics Conference, 20120827/0831, Warszawa (PL), pp.306307, 2012 Streszczenie: This paper proposes a Substructure Isolation Method (SIM) for online local health monitoring at the substructural level. The SIM [1] includes two key steps: isolation of the substructure, and its local identification. Isolated substructure is an independent virtual structure, which is isolated from the global structure with virtual supports placed in the interface DOFs. Its response is constructed by such a linear combination of time series of measured local responses that the desired boundary conditions are satisfied and all outside influences are removed. Given the combined response, the substructure is locally identified using any of the standard methods aimed originally at global analysis. This is unlike other substructuring methods, see e.g. [2,3], which require dedicated methods in order to deal simultaneously with structural damages and generalized interface forces. Afiliacje autorów:
 
21.  Suwała G., Jankowski Ł., Modelfree identification of structural damages, SolMech 2010, 37th Solid Mechanics Conference, 20100906/0910, Warszawa (PL), pp.288289, 2010 Streszczenie: This work presents and verifies experimentally a modelfree methodology for offline identification of structural damages. The Virtual Distortion Method (VDM) [1] is used, which allows the structure to be modeled locally in an essentially nonparametric way, so that no errorprone parametric modeling is necessary. The damage is modeled using damageequivalent pseudoloads, which are convolved with the experimentally obtained responses of the original structure to compute the response of the damaged structure. A related approach has been earlier used for modelfree impact and mass identification [2,3]. An effective sensitivity analysis is possible via the adjoint variable method. Afiliacje autorów:
 
22.  Zhang Q., Jankowski Ł., Offline reconstruction of dynamic loads, SolMech 2008, 36th Solid Mechanics Conference, 20080909/0912, Gdańsk (PL), pp.392393, 2008 
Patenty
Numer/data zgłoszenia patentowego Ogłoszenie o zgłoszeniu patentowym  Twórca / twórcy Tytuł Kraj i Nazwa uprawnionego z patentu  Numer patentu Ogłoszenie o udzieleniu patentu  

428526 20190108    Faraj R., Graczykowski C., Jankowski Ł., HolnickiSzulc J. Absorber śrubowy o zmiennym skoku gwintu tocznego PL, Instytut Podstawowych Problemów Techniki PAN     