Tabela A z publikacjami w czasopismach wyróżnionych w Journal Citation Reports (JCR) 
Tabela B z publikacjami w czasopismach zagranicznych i krajowych, wyróżnionych na liście MNSzW
Publikacje konferencyjne indeksowane w bazie Web of Science Core Collection
Inne publikacje w pozostałych czasopismach i wydawnictwach konferencyjnych
Afiliacja IPPT PAN

1.Bollero A., Rial J., Villanueva M., Golasiński K.M., Seoane A., Almunia J., Altimira R., Recycling of Strontium Ferrite Waste in a Permanent Magnet Manufacturing Plant, ACS Sustainable Chemistry & Engineering, ISSN: 2168-0485, DOI: 10.1021/acssuschemeng.6b03053, Vol.5, No.4, pp.3243-3249, 2017
Bollero A., Rial J., Villanueva M., Golasiński K.M., Seoane A., Almunia J., Altimira R., Recycling of Strontium Ferrite Waste in a Permanent Magnet Manufacturing Plant, ACS Sustainable Chemistry & Engineering, ISSN: 2168-0485, DOI: 10.1021/acssuschemeng.6b03053, Vol.5, No.4, pp.3243-3249, 2017

Abstract:
Residues resulting from the manufacture of strontium ferrite magnets have been recycled for further use in magnet fabrication instead of disposal as waste. The quality of the recycled ferrite powder has been tested and compared to that of the new starting ferrite material. The magnetic properties of the recycled powder not only match those of the starting material acquired by the company for the production of magnets but exceed them. A coercivity value 3.5 times larger than that of the new starting ferrite powder, accompanied by a 25% increase in remanence, makes this material a new and improved ferrite product to re-enter the production chain in the factory with an extended applications range. This improvement is proven to be due to tuning of the morphology and microstructure through processing and subsequent heat treatment. The use of processing conditions in the same range as those typically used in the preparation of ferrite powders and magnets, in combination with the superior magnetic quality of the resulting powders, makes this method a suitable path to guarantee sustainability and an efficient use of resources in permanent magnet companies.

Keywords:
Ferrites, Permanent magnets; Recovery; Recycling; Sustainability

(40p.)
2.Hoffman J., Chrzanowska J., Mościcki T., Radziejewska J., Stobinski L., Szymański Z., Plasma generated during underwater pulsed laser processing, APPLIED SURFACE SCIENCE, ISSN: 0169-4332, DOI: 10.1016/j.apsusc.2017.01.185, pp.1-6, 2017
Hoffman J., Chrzanowska J., Mościcki T., Radziejewska J., Stobinski L., Szymański Z., Plasma generated during underwater pulsed laser processing, APPLIED SURFACE SCIENCE, ISSN: 0169-4332, DOI: 10.1016/j.apsusc.2017.01.185, pp.1-6, 2017

Abstract:
The plasma induced during underwater pulsed laser ablation of graphite is studied both experimentally and theoretically. The results of the experiment show that the maximum plasma temperature of 25000 K is reached 20 ns from the beginning of the laser pulse and decreases to 6500 K after 1000 ns. The observed OH absorption band shows that the plasma plume is surrounded by the thin layer of dissociated water vapour at a temperature around 5500 K. The hydrodynamic model applied shows similar maximum plasma temperature at delay times between 14 ns and 30 ns. The calculations show also that already at 14th ns, the plasma electron density reaches 0.97·1027 m−3, which is the critical density for 1064 nm radiation. At the same time the plasma pressure is 2 GPa, which is consisted with earlier measurements of the peak pressure exerted on a target in similar conditions.

Keywords:
Underwater laser processing, Pulsed laser ablation in liquid, Laser induced plasma, Numerical modelling

(35p.)
3.Łazarska M., Woźniak T.Z., Ranachowski Z., Trafarski A., Domek G., Analysis of acoustic emission signals at austempering of steels using neural networks, METALS AND MATERIALS INTERNATIONAL, ISSN: 1598-9623, DOI: 10.1007/s12540-017-6347-z, pp.1-8, 2017
Łazarska M., Woźniak T.Z., Ranachowski Z., Trafarski A., Domek G., Analysis of acoustic emission signals at austempering of steels using neural networks, METALS AND MATERIALS INTERNATIONAL, ISSN: 1598-9623, DOI: 10.1007/s12540-017-6347-z, pp.1-8, 2017

Abstract:
Bearing steel 100CrMnSi6-4 and tool steel C105U were used to carry out this research with the steels being austempered to obtain a martensitic-bainitic structure. During the process quite a large number of acoustic emissions (AE) were observed. These signals were then analysed using neural networks resulting in the identification of three groups of events of: high, medium and low energy and in addition their spectral characteristics were plotted. The results were presented in the form of diagrams of AE incidence as a function of time. It was demonstrated that complex transformations of austenite into martensite and bainite occurred when austempering bearing steel at 160 °C and tool steel at 130 °C respectively. The selected temperatures of isothermal quenching of the tested steels were within the area near to MS temperature, which affected the complex course of phase transition. The high activity of AE is a typical occurrence for martensitic transformation and this is the transformation mechanism that induces the generation of AE signals of higher energy in the first stage of transition. In the second stage of transformation, the initially nucleated martensite accelerates the occurrence of the next bainitic transformation.

Keywords:
microstructure, phase transformation, dislocation, ultrasonics, alloys

(30p.)
4.Wójcik J., Lewandowski M., Żołek N., Grating Lobes Suppression by Adding Virtual Receiving Subaperture in Synthetic Aperture Imaging, Ultrasonics, ISSN: 0041-624X, DOI: 10.1016/j.ultras.2016.12.013, Vol.76, pp.125-135, 2017
Wójcik J., Lewandowski M., Żołek N., Grating Lobes Suppression by Adding Virtual Receiving Subaperture in Synthetic Aperture Imaging, Ultrasonics, ISSN: 0041-624X, DOI: 10.1016/j.ultras.2016.12.013, Vol.76, pp.125-135, 2017

Abstract:
A method of suppression of grating lobes is presented, analyzed, and verified. The method is based on creating a Virtual Receiving Subaperture (VRS) by adding virtual transducer elements not existing in the physical layout of the receiver. The VRS channels are filled with data based on signals from real channels. The analytical model of the synthetic aperture imaging system’s impulse response is presented to describe the properties of the VRS. The model shows a reduction of the receiving grating lobes’ amplitude (with a comparison to the main lobe’s amplitude) by a magnitude equal to the number of receiving transducer elements. It is shown that effective properties of the entire system with a VRS are similar to a system with a pitch in the receiving aperture that is twice as small. The numerical calculations of the impulse response show a doubling of the signal to noise ratio, which results in a reduction of the receiving grating lobes. For experimental validation, the generalized Plane Wave Imaging with and without the VRS is compared with a basic synthetic transmit aperture (STA) imaging. The experiment confirmed that the use of a VRS allows for visualizat ion of the objects in a medium in which they are not imaged without a VRS or are visualized with a lower contrast. The reduction of grating lobes attained using the proposed method is at the level of 15dB in the visualization of the superficial cyst.

Keywords:
Grating lobes, Image quality, Synthetic aperturę, Virtual subaperture

(30p.)
5.Golasiński K.M., Pieczyska E.A., Staszczak M., Maj M., Furuta T., Kuramoto S., Infrared thermography applied for experimental investigation of thermomechanical couplings in Gum Metal, Quantitative InfraRed Thermography Journal, ISSN: 1768-6733, DOI: 10.1080/17686733.2017.1284295, pp.1-8, 2017
Golasiński K.M., Pieczyska E.A., Staszczak M., Maj M., Furuta T., Kuramoto S., Infrared thermography applied for experimental investigation of thermomechanical couplings in Gum Metal, Quantitative InfraRed Thermography Journal, ISSN: 1768-6733, DOI: 10.1080/17686733.2017.1284295, pp.1-8, 2017

Abstract:
Results of initial investigation of thermomechanical couplings in innovative β-Ti alloy called Gum Metal subjected to tension are presented. The experimental set-up, consisting of testing machine and infrared camera, enabled to obtain stress–strain curves with high accuracy and correlate them to estimated temperature changes of the specimen during the deformation process. Both ultra-low elastic modulus and high strength of Gum Metal were confirmed. The infrared measurements determined average and maximal temperature changes accompanying the alloy deformation process, allowed to estimate thermoelastic effect, which is related to the alloy yield point. The temperature distributions on the specimen surface served to analyse strain localization effects leading to the necking and rupture.

Keywords:
Gum Metal, thermomechanical coupling, nonlinear elasticity, yield point, infrared camera

(25p.)