Institute of Fundamental Technological Research
Polish Academy of Sciences

Partners

Łukasz Kurpaska

National Centre for Nuclear Research (PL)

Recent publications
1.  Psiuk R., Mościcki T., Chrzanowska-Giżyńska J., Kurpaska , Radziejewska J., Denis P., Garbiec D., Chmielewski M., Mechanical and Thermal Properties of W-Ta-B Coatings Deposited by High-Power Impulse Magnetron Sputtering (HiPIMS), Materials, ISSN: 1996-1944, DOI: 10.3390/ma16020664, Vol.16, No.2, pp.1-12, 2023

Abstract:
We present the deposition and characterization of tungsten-tantalum diboride (W,Ta)B2 coatings prepared by the high-power impulse magnetron sputtering technique. We evaluated the influence of pulse duration and substrate bias on the properties of (W,Ta)B2 films. A high hardness of up to 35 GPa measured by nanoindentation was simultaneously obtained with good elastic properties. Changing the pulse duration greatly affected the B/(W+Ta) atomic ratio, which influenced the properties of the coatings. The deposited films are thermally stable at up to 1000 ◦C in vacuum and are able to withstand oxidation at 500 ◦C.

Keywords:
tungsten diboride, high power impulse magnetron sputtering (HiPIMS), hardness, thermal stability, oxidation resistance

Affiliations:
Psiuk R. - IPPT PAN
Mościcki T. - IPPT PAN
Chrzanowska-Giżyńska J. - IPPT PAN
Kurpaska  - National Centre for Nuclear Research (PL)
Radziejewska J. - other affiliation
Denis P. - IPPT PAN
Garbiec D. - Metal Forming Institute, Poznań (PL)
Chmielewski M. - Institute of Electronic Materials Technology (PL)
2.  Nowak M., Mulewska K., Azarov A., Kurpaska , Ustrzycka A., A peridynamic elasto-plastic damage model for ion-irradiated materials, INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, ISSN: 0020-7403, DOI: 10.1016/j.ijmecsci.2022.107806, No.107806, pp.1-46, 2022

Abstract:
This study presents the novel peridynamic constitutive relations formulated in order to predict the plastic deformation and damage evolution in irradiated materials. The plastic behaviour of the material in which radiation induced defects contribute to the defined peridynamic porosity is described by the Gurson-Tvergaard-Needleman (GTN) yield criterion with irradiation hardening. The definition of peridynamic porosity is proposed as a volume of discontinuities created in the volume of peridynamic particles. The new constitutive relations for irradiation hardening based on the dilatational part of elastic strain energy are formulated. The physical relevance of coupling the porosity with the nonlinear irradiation hardening is discussed. The expressions for the yield function, kinetics of evolution of radiation induced porosity, irradiation hardening and plastic flow rule are derived in terms of the peridynamics variables. The peridynamic predictions are calibrated based on the experimental data obtained during the advanced experimental campaigns dedicated to irradiated materials to verify the validity of the proposed constitutive model. Ion irradiation campaigns were carried out to mimic the effects of neutron irradiation. A series of indentation experiments were conducted to elucidate the effects of material structure modification and assess the hardening effect originating from radiation defects.

Keywords:
Peridynamics,Constitutive modeling,Radiation induced damage,Peridynamic porosity,Gurson yield function,Irradiation hardening,Ion irradiation,Nano-indentation test

Affiliations:
Nowak M. - IPPT PAN
Mulewska K. - National Centre for Nuclear Research (PL)
Azarov A. - other affiliation
Kurpaska  - National Centre for Nuclear Research (PL)
Ustrzycka A. - IPPT PAN
3.  Mościcki T., Chrzanowska-Giżyńska J., Psiuk R., Denis P., Mulewska K., Kurpaska Ł., Chmielewski M., Wiśniewska M., Garbiec D., Thermal and mechanical properties of (W,Zr)B2-z coatings deposited by RF magnetron sputtering method, International Journal of Refractory Metals and Hard Materials, ISSN: 0263-4368, DOI: 10.1016/j.ijrmhm.2022.105811, Vol.105, pp.105811-1-8, 2022

Abstract:
Magnetron sputtered WB2 coatings doped with 8, 11 and 16 at.% zirconium were analysed using energy dispersive spectroscopy, X-ray diffraction and nanoindentation under the load of 4, 7 and 10 mN. It has been observed that these coatings crystallize in the α-AlB2 and ω-W2B5 prototype structure. Phenomenon responsible for this is an increase of the zirconium content which causes an increase in the ω-W2B5 phase. All the deposited coatings have a hardness of about 45 GPa while Young's modulus drops down from 497 to 480 GPa with increasing zirconium content. Coatings without doping and doped with 16 at.% zirconium were annealed at 650 °C and subjected to cyclic thermal loads using a maximum temperature 600 °C and cooling with a compressed air. It has been observed that addition of zirconium improved coatings phase stability.

Keywords:
superhard coatings, tungsten diboride, zirconia doping, magnetron sputtering, cycling thermal loads, annealing

Affiliations:
Mościcki T. - IPPT PAN
Chrzanowska-Giżyńska J. - IPPT PAN
Psiuk R. - IPPT PAN
Denis P. - IPPT PAN
Mulewska K. - National Centre for Nuclear Research (PL)
Kurpaska Ł. - National Centre for Nuclear Research (PL)
Chmielewski M. - Institute of Electronic Materials Technology (PL)
Wiśniewska M. - Łukasiewicz Research Network – Metal Forming Institute (PL)
Garbiec D. - Metal Forming Institute, Poznań (PL)
4.  Nosewicz S., Bazarnik P., Clozel M., Kurpaska Ł., Jenczyk P., Jarząbek D., Chmielewski M., Romelczyk-Baishya B., Lewandowska M., Pakieła Z., Huang Y., Langdon T.G., A multiscale experimental analysis of mechanical properties and deformation behavior of sintered copper–silicon carbide composites enhanced by high-pressure torsion, ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING, ISSN: 1644-9665, DOI: 10.1007/s43452-021-00286-4, Vol.21, pp.131-1-19, 2021

Abstract:
Experiments were conducted to investigate, within the framework of a multiscale approach, the mechanical enhancement, deformation and damage behavior of copper–silicon carbide composites (Cu–SiC) fabricated by spark plasma sintering (SPS) and the combination of SPS with high-pressure torsion (HPT). The mechanical properties of the metal–matrix composites were determined at three different length scales corresponding to the macroscopic, micro- and nanoscale. Small punch testing was employed to evaluate the strength of composites at the macroscopic scale. Detailed analysis of microstructure evolution related to SPS and HPT, sample deformation and failure of fractured specimens was conducted using scanning and transmission electron microscopy. A microstructural study revealed changes in the damage behavior for samples processed by HPT and an explanation for this behavior was provided by mechanical testing performed at the micro- and nanoscale. The strength of copper samples and the metal–ceramic interface was determined by microtensile testing and the hardness of each composite component, corresponding to the metal matrix, metal–ceramic interface, and ceramic reinforcement, was measured using nano-indentation. The results confirm the advantageous effect of large plastic deformation on the mechanical properties of Cu–SiC composites and demonstrate the impact on these separate components on the deformation and damage type.

Keywords:
copper–silicon carbide composite, high-pressure torsion, metal–matrix composites, multiscale analysis, nano-indentation, small punch test

Affiliations:
Nosewicz S. - IPPT PAN
Bazarnik P. - Warsaw University of Technology (PL)
Clozel M. - National Centre for Nuclear Research (PL)
Kurpaska Ł. - National Centre for Nuclear Research (PL)
Jenczyk P. - IPPT PAN
Jarząbek D. - IPPT PAN
Chmielewski M. - Institute of Electronic Materials Technology (PL)
Romelczyk-Baishya B. - Warsaw University of Technology (PL)
Lewandowska M. - other affiliation
Pakieła Z. - Warsaw University of Technology (PL)
Huang Y. - Bournemouth University (GB)
Langdon T.G. - University of Southampton (GB)
5.  Ustrzycka A., Skoczeń B., Nowak M., Kurpaska Ł., Wyszkowska E., Jagielski J., Elastic–plastic-damage model of nano-indentation of the ion-irradiated 6061 aluminium alloy, INTERNATIONAL JOURNAL OF DAMAGE MECHANICS, ISSN: 1056-7895, DOI: 10.1177/1056789520906209, pp.1-35, 2020

Abstract:
The paper presents experimental and numerical characterization of damage evolution for ion-irradiated materials subjected to plastic deformation during nano-indentation. Ion irradiation technique belongs to the methods where creation of radiation-induced defects is controlled with a high accuracy (including both, concentration and depth distribution control), and allows to obtain materials having a wide range of damage level, usually expressed in terms of displacements per atom (dpa) scale. Ion affected layers are usually thin, typically less than 1 micrometer thick. Such a low thickness requires to use nano-indentation technique to measure the mechanical properties of the irradiated layers. The He or Ar ion penetration depth reaches approximately 150 nm, which is sufficient to perform several loading-partial-unloading cycles at increasing forces. Damage evolution is reflected by the force-displacement diagram, that is backed by the stress–strain relation including damage. In this work the following approach is applied: dpa is obtained from physics (irradiation mechanisms), afterwards, the radiation-induced damage is defined in the framework of continuum damage mechanics to solve the problem of further evolution of damage fields under mechanical loads. The nature of radiation-induced damage is close to porosity because of formation of clusters of vacancies. The new mathematical relation between radiation damage (dpa) and porosity parameter is proposed. Deformation process experienced by the ion irradiated materials during the nano-indentation test is then numerically simulated by using extended Gurson–Tvergaard– Needleman (GTN) model, that accounts for the damage effects. The corresponding numerical results are validated by means of the experimental measurements. It turns out, that the GTN model quite successfully reflects closure of voids, and increase of material density during the nano-indentation.

Keywords:
radiation-induced damage, evolution of vacancy clusters, nano-indentation test, ion irradiation, radiation hardening

Affiliations:
Ustrzycka A. - IPPT PAN
Skoczeń B. - Cracow University of Technology (PL)
Nowak M. - IPPT PAN
Kurpaska Ł. - National Centre for Nuclear Research (PL)
Wyszkowska E. - National Centre for Nuclear Research (PL)
Jagielski J. - National Centre for Nuclear Research (PL)
6.  Chrzanowska-Giżyńska J., Denis P., Giżyński M., Kurpaska Ł., Mihailescu I., Ristoscu C., Szymański Z., Mościcki T., Thin WBx and WyTi1−yBx films deposited by combined magnetron sputtering and pulsed laser deposition technique, APPLIED SURFACE SCIENCE, ISSN: 0169-4332, DOI: 10.1016/j.apsusc.2019.02.006, Vol.478, pp.505-513, 2019

Abstract:
The coatings of tungsten borides (WBx) and tungsten borides doped with titanium (WyTi1−yBx) were deposited by using combined magnetron sputtering - pulsed laser deposition technique. In the case of WBx coatings, pure tungsten target was evaporated by a laser pulse at 1064 nm wavelength and pure boron target was sputtered by a magnetron. In the case of WyTi1−yBx coatings, the W2B5 target was sputtered by the magnetron and titanium target was evaporated by the laser pulse at 1064 nm wavelength. The content of titanium dopant changed from 1.1 to 5.5 at.%. The microstructure, chemical and phase composition of deposited coatings were investigated by means of Scanning Electron Microscopy, Energy Dispersive X-Ray Spectroscopy, X-Ray Photoelectron Spectroscopy and X-Ray Diffractometry, respectively. The Vickers hardness and Young's modulus were determined by using the nanoindentation test. Nanocrystalline WB coatings with dominant WB2 phase were obtained at a substrate temperature of 520 °C. The coatings were superhard with a hardness of 47–50 GPa and the mean value of surface roughness was <6 nm. The WBx coatings doped with 5.5 at.% Ti had hardness similar to the coatings sputtered by magnetron from W2B5 target.

Keywords:
The superhard WyBx thin films was deposited with hybrid laser-magnetron technology, The MS-PLD method allows for the deposition of ternary borides such as WyTi1−yBx, The MS-PLD method enables to control the chemical and phase composition of films, The deposited films are smooth with hardness above 50 GPa, Crystalline films were deposited only on a substrate kept an elevated temperature

Affiliations:
Chrzanowska-Giżyńska J. - IPPT PAN
Denis P. - IPPT PAN
Giżyński M. - Warsaw University of Technology (PL)
Kurpaska Ł. - National Centre for Nuclear Research (PL)
Mihailescu I. - National Institute for Lasers, Plasma and Radiation Physics (RO)
Ristoscu C. - National Institute for Lasers, Plasma and Radiation Physics (RO)
Szymański Z. - IPPT PAN
Mościcki T. - IPPT PAN
7.  Chmielewski M., Nosewicz S., Wyszkowska E., Kurpaska Ł., Strojny-Nędza A., Piątkowska A., Bazarnik P., Pietrzak K., Analysis of the micromechanical properties of copper-silicon carbide composites using nanoindentation measurements, CERAMICS INTERNATIONAL, ISSN: 0272-8842, DOI: 10.1016/j.ceramint.2019.01.257, Vol.45, No.7A, pp.9164-9173, 2019

Abstract:
The study presents a detailed analysis of the impact of the coating type of silicon carbide particles and its share by volume on the microstructure and micromechanical properties of Cu-SiC composites. In order to protect the carbide from decomposition during the manufacturing of the composites, the surface of SiC was modified via a plasma vapour deposition technique with a layer of metals (W, Cr, Ti and Ni). Composites with a variable share of the ceramic phase (10–50 %vol.) were obtained at a temperature of 950 °C using spark plasma sintering. An analysis of the structures of the composites, especially in the metal-ceramic boundary region, was conducted with the use of scanning and transmission electron microscopy. The mechanical properties of the composites in the Cu-interface-SiC system were studied via a nanoindentation technique. The comparison of the results of hardness and Young's modulus studies were completed in relation to the actual structures of the materials, which in turn made it possible to determine the impact of the interfacial structure on the global properties of the composite materials.

Keywords:
copper-silicon carbide composites, nanoindentation, SPS, interface study

Affiliations:
Chmielewski M. - Institute of Electronic Materials Technology (PL)
Nosewicz S. - IPPT PAN
Wyszkowska E. - National Centre for Nuclear Research (PL)
Kurpaska Ł. - National Centre for Nuclear Research (PL)
Strojny-Nędza A. - Institute of Electronic Materials Technology (PL)
Piątkowska A. - Institute of Electronic Materials Technology (PL)
Bazarnik P. - Warsaw University of Technology (PL)
Pietrzak K. - IPPT PAN
8.  Chrzanowska-Giżyńska J., Denis P., Woźniacka S., Kurpaska Ł., Mechanical properties and thermal stability of tungsten boride films deposited by radio frequency magnetron sputtering, CERAMICS INTERNATIONAL, ISSN: 0272-8842, DOI: 10.1016/j.ceramint.2018.07.208, Vol.44, No.16, pp.19603-19611, 2018

Abstract:
Tungsten and boron compounds belong to the group of superhard materials since their hardness could exceed 40 GPa. In this study, the properties of the tungsten boride WBx coatings deposited by radio frequency magnetron sputtering were investigated. The sputtering was performed from specially prepared targets that were composed of boron and tungsten mixed in a molar ratio of 2.5 and sintered in Spark Plasma Sintering (SPS) process. WB films were deposited on silicon (100) and stainless steel 304 substrates at temperatures of 23 ÷ 770 °C. Microstructure, chemical and phase composition were investigated by using Scanning Electron Microscope (SEM), X-Ray Photoelectron Spectroscopy (XPS) and X-Ray Diffraction (XRD), respectively. The mechanical properties like Vickers hardness and Young's modulus were obtained by using nanoindentation test at a load of 5 ÷ 100 mN. The friction coefficient and wear resistance of αWB coatings were investigated in scratch test and reciprocal sliding wear instrumentation. Moreover, in order to investigate thermal properties, the αWB films were annealed at 1000 °C in argon/air for 1 h and at 250 °C for 2 h in air atmosphere. Results of our research confirm that αWB coatings can be considered as an alternative to superhard materials in the production of wear resistant, long-lasting tools.

Keywords:
Hard coatings, Hard materials, Magnetron sputtering, Mechanical properties, Thermal properties, Tungsten boride

Affiliations:
Chrzanowska-Giżyńska J. - IPPT PAN
Denis P. - IPPT PAN
Woźniacka S. - IPPT PAN
Kurpaska Ł. - National Centre for Nuclear Research (PL)
9.  Jóźwik I., Strojny-Nędza A., Chmielewski M., Pietrzak K., Kurpaska Ł., Nosewicz S., High resolution SEM characterization of nano-precipitates in ODS steels, MICROSCOPY RESEARCH AND TECHNIQUE, ISSN: 1059-910X, DOI: 10.1002/jemt.23004, Vol.81, No.5, pp.502-508, 2018

Abstract:
The performance of the present-day scanning electron microscopy (SEM) extends far beyond delivering electronic images of the surface topography. Oxide dispersion strengthened (ODS) steel is on of the most promising materials for the future nuclear fusion reactor because of its good radiation resistance, and higher operation temperature up to 750°C. The microstructure of ODS should not exceed tens of nm, therefore there is a strong need in a fast and reliable technique for their characterization. In this work, the results of low-kV SEM characterization of nanoprecipitates formed in the ODS matrix are presented. Application of highly sensitive photo-diode BSE detector in SEM imaging allowed for the registration of single nm-sized precipitates in the vicinity of the ODS alloys. The composition of the precipitates has been confirmed by TEM-EDS.

Keywords:
ODS steels, scanning electron microscopy, spark plasma sintering

Affiliations:
Jóźwik I. - Institute of Electronic Materials Technology (PL)
Strojny-Nędza A. - Institute of Electronic Materials Technology (PL)
Chmielewski M. - Institute of Electronic Materials Technology (PL)
Pietrzak K. - other affiliation
Kurpaska Ł. - National Centre for Nuclear Research (PL)
Nosewicz S. - IPPT PAN
10.  Chmielewski M., Nosewicz S., Kurpaska Ł., Romelczyk B., Evolution of material properties during the sintering process of Cr-Re-Al2O3 composites, COMPOSITES PART B-ENGINEERING, ISSN: 1359-8368, DOI: 10.1016/j.compositesb.2016.04.065, Vol.98, pp.88-96, 2016

Abstract:
This paper constitutes an analysis of the effect of heat treatment time on the properties of Cr-Re-Al2O3 composite materials. It was found that as a result of sintering, rhenium is dissolved in chromium to create chromium-rhenium solid solution. This process is time-dependent, therefore as the time extends, the structure of material becomes homogenous, which improves its mechanical properties. Within the frame of herein presented studies, a series of technological tests have been carried out for a constant sintering temperature (1450°C) and pressure (30 MPa), with the use of a variable holding time in the maximum temperature. As a result, changes in the structure of Crsingle bondRe matrix have been determined and the resulting changes in the properties of composite. Based on those tests, optimal conditions of the sintering process have been determined from the point of view of obtaining a homogenous structure and the most beneficial properties of Cr-Re-Al2O3 composites.

Keywords:
Metal-matrix composites (MMCs), Mechanical properties, Mechanical testing, Sintering

Affiliations:
Chmielewski M. - Institute of Electronic Materials Technology (PL)
Nosewicz S. - IPPT PAN
Kurpaska Ł. - National Centre for Nuclear Research (PL)
Romelczyk B. - Warsaw University of Technology (PL)
11.  Chrzanowska J., Kurpaska Ł., Giżyński M., Hoffman J., Szymański Z., Mościcki T., Fabrication and characterization of superhard tungsten boride layers deposited by radio frequency magnetron sputtering, CERAMICS INTERNATIONAL, ISSN: 0272-8842, DOI: 10.1016/j.ceramint.2016.04.166, Vol.42, No.10, pp.12221-12230, 2016

Abstract:
The most promising areas of research of new super-hard materials are transition metal borides. These materials are one of the candidates for future superhard layers that will be competitive to DLC and c-BN layers. In this paper MoB-type tungsten boride (WB) layers were examined. WB layers have been deposited by radio frequency magnetron sputtering on Silicon (100), 304 stainless steel (SS 304) and Inconel 601 substrates. Measured thickness of herein prepared layers was about 1 µm, and all studied samples were dense, uniform and smooth. Surface investigation was performed by using an optical profilometer, atomic force microscopy, and scanning electron microscopy. The structure analysis was examined by using X-ray diffractometer (XRD) and transmission electron microscopy (TEM) techniques. Results from the XRD and TEM analysis showed that WB layers were dominated by (101) reflection and indicated a fine grain structure with a grain size of 20–40 nm. The effect of target sputtering power and ambient gas pressure was investigated. The hardness of WB layers deposited on silicon substrate was compared under the load from 1 mN to 5 mN. The hardness of WB layers deposited on SS 304 and Inconel was measured up to 50 mN. All layers of WB revealed excellent hardness exceeding 40 GPa.

Keywords:
Borides, Nanohardness, RF magnetron sputtering, Superhard layers, Tungsten boride

Affiliations:
Chrzanowska J. - IPPT PAN
Kurpaska Ł. - National Centre for Nuclear Research (PL)
Giżyński M. - Warsaw University of Technology (PL)
Hoffman J. - IPPT PAN
Szymański Z. - IPPT PAN
Mościcki T. - IPPT PAN

Conference abstracts
1.  Psiuk R., Denis P., Kurpaska Ł., Mościcki T., Superhard tungsten-tantalum diboride (W,Ta)B2 coatings prepared by High power impulse magnetron sputtering HiPIMS, ICMCTF 2023, International Conference on Metallurgical Coatings and Thin Films, 2023-05-21/05-26, San Diego, California (US), pp.104-104, 2023
2.  Ustrzycka A., Dominguez-Gutierrez F.J., Nowak M., Mulewska K., Azarov A., Kurpaska Ł., PHYSICAL AND MECHANICAL EFFECTS OF RADIATION DAMAGE, ICEM, 19th International Conference on Experimental Mechanics, 2022-07-17/07-21, Kraków (PL), No.TS1, pp.99-100, 2022
3.  Chrzanowska-Giżyńska J., Psiuk R., Denis P., Kurpaska Ł., Mościcki T., Thermal and mechanical properties of (W‚Zr)B2-z coatings deposited by RF magnetron sputtering method, ICMCTF, 47th International Conference on Metallurgical Coatings and Thin Films, 2021-04-26/04-30, San Diego - virtual (US), pp.1-1, 2021
4.  Chrzanowska J., Garbiec D., Kurpaska Ł., Denis P., Hoffman J., Mościcki T., Szymański Z., The effect of substrate temperature on the properties of tungsten boride layers deposited by radio frequency magnetron sputtering and pulsed laser deposition, EYEC, 6th European Young Engineers Conference, 2017-04-24/04-26, Warszawa (PL), pp.240-240, 2017

Keywords:
RF magnetron sputtering, hard materials, PLD, tungsten boride

Affiliations:
Chrzanowska J. - IPPT PAN
Garbiec D. - Metal Forming Institute, Poznań (PL)
Kurpaska Ł. - National Centre for Nuclear Research (PL)
Denis P. - IPPT PAN
Hoffman J. - IPPT PAN
Mościcki T. - IPPT PAN
Szymański Z. - IPPT PAN

Category A Plus

IPPT PAN

logo ippt            Pawińskiego 5B, 02-106 Warsaw
  +48 22 826 12 81 (central)
  +48 22 826 98 15
 

Find Us

mapka
© Institute of Fundamental Technological Research Polish Academy of Sciences 2024