Stefania Woźniacka

Zakład Mechaniki Materiałów (ZMM)
Pracownia Warstwy Wierzchniej (PWW)
stanowisko: starszy technik dokumentalista
telefon: (+48) 22 826 12 81 wew.: 141
pokój: 231
e-mail: stewoz

Ostatnie publikacje
1.Chrzanowska-Giżyńska J., Denis P., Woźniacka S., Kurpaska Ł., Mechanical properties and thermal stability of tungsten boride films deposited by radio frequency magnetron sputtering, CERAMICS INTERNATIONAL, ISSN: 0272-8842, DOI: 10.1016/j.ceramint.2018.07.208, Vol.44, No.16, pp.19603-19611, 2018

Streszczenie:

Tungsten and boron compounds belong to the group of superhard materials since their hardness could exceed 40 GPa. In this study, the properties of the tungsten boride WBx coatings deposited by radio frequency magnetron sputtering were investigated. The sputtering was performed from specially prepared targets that were composed of boron and tungsten mixed in a molar ratio of 2.5 and sintered in Spark Plasma Sintering (SPS) process. WB films were deposited on silicon (100) and stainless steel 304 substrates at temperatures of 23 ÷ 770 °C. Microstructure, chemical and phase composition were investigated by using Scanning Electron Microscope (SEM), X-Ray Photoelectron Spectroscopy (XPS) and X-Ray Diffraction (XRD), respectively. The mechanical properties like Vickers hardness and Young's modulus were obtained by using nanoindentation test at a load of 5 ÷ 100 mN. The friction coefficient and wear resistance of αWB coatings were investigated in scratch test and reciprocal sliding wear instrumentation. Moreover, in order to investigate thermal properties, the αWB films were annealed at 1000 °C in argon/air for 1 h and at 250 °C for 2 h in air atmosphere. Results of our research confirm that αWB coatings can be considered as an alternative to superhard materials in the production of wear resistant, long-lasting tools.

Słowa kluczowe:

Hard coatings, Hard materials, Magnetron sputtering, Mechanical properties, Thermal properties, Tungsten boride

Afiliacje autorów:

Chrzanowska-Giżyńska J.-IPPT PAN
Denis P.-IPPT PAN
Woźniacka S.-IPPT PAN
Kurpaska Ł.-National Centre for Nuclear Research (PL)
40p.
2.Kucharski S., Jarząbek D., Piątkowska A., Woźniacka S., Decrease of Nano-hardness at Ultra-low Indentation Depths in Copper Single Crystal, EXPERIMENTAL MECHANICS, ISSN: 0014-4851, DOI: 10.1007/s11340-015-0105-2, Vol.56, No.3, pp.381-393, 2016

Streszczenie:

In the present study, we report a detailed investigation of the unusual size effect in single crystals. For the experiments we specified the hardness in single crystalline copper specimens with different orientations ((001), (011) and (111)) using Oliver-Pharr method. Our results indicates that with decreasing load, after the value of the hardness reached its maximum, it starts to decrease for very small indentation depths (<150 nm). For the sake of accuracy of hardness determination we have developed two AFM-based methods to evaluate contact area between tip and indented material. The proposed exact measurement of the contact area, which includes the effect of pile-up and sink-in patterns, can partially explain the strange behaviour, however, the decrease of hardness at low loads is still observed. At higher loads range the specified hardness is practically constant.

Słowa kluczowe:

Copper, Single crystal, Nanoindentation, AFM, Size effect

Afiliacje autorów:

Kucharski S.-IPPT PAN
Jarząbek D.-IPPT PAN
Piątkowska A.-Institute of Electronic Materials Technology (PL)
Woźniacka S.-IPPT PAN
35p.