Instytut Podstawowych Problemów Techniki
Polskiej Akademii Nauk

Partnerzy

Adrian Chlanda

Warsaw University of Technology (PL)

Ostatnie publikacje
1.  Górecka Ż., Idaszek J., Kołbuk D., Choińska E., Chlanda A., Święszkowski W., The effect of diameter of fibre on formation of hydrogen bonds and mechanical properties of 3D-printed PCL, Materials Science and Engineering C-Materials for Biological Applications, ISSN: 0928-4931, DOI: 10.1016/j.msec.2020.111072, Vol.114, pp.111072-1-11, 2020

Streszczenie:
Fused Deposition Modelling (FDM) technique has been widely utilized in fabrication of 3D porous scaffolds for tissue engineering (TE) applications. Surprisingly, although there are many publications devoted to the architectural features of the 3D scaffolds fabricated by the FDM, none of them give us evident information about the impact of the diameter of the fibres on material properties. Therefore, the aim of this study was to investigate, for the first time, the effect of the diameter of 3D-printed PCL fibres on variations in their microstructure and resulting mechanical behaviour. The fibres made of poly(ε-caprolactone) (PCL) were extruded through commonly used types of nozzles (inner diameter ranging from 0.18 mm to 1.07 mm) by means of FDM technique. Static tensile test and atomic force microscopy working in force spectroscopy mode revealed strong decrease in the Young's modulus and yield strength with increasing fibre diameter in the investigated range. To explain this phenomenon, we conducted differential scanning calorimetry, wide-angle X-ray-scattering, Fourier-transform infrared spectroscopy, infrared and polarized light microscopy imaging. The obtained results clearly showed that the most prominent effect on the obtained microstructures and mechanical properties had different cooling and shear rates during fabrication process causing changes in supramolecular interactions of PCL. The observed fibre size-dependent formation of hydrogen bonds affected the crystalline structure and its stability. Summarising, this study clearly demonstrates that the diameter of 3D-printed fibres has a strong effect on obtained microstructure and mechanical properties, therefore should be taken into consideration during design of the 3D TE scaffolds.

Słowa kluczowe:
fused deposition modelling, polycaprolactone, mechanical properties, hydrogen bonds, microstructure

Afiliacje autorów:
Górecka Ż. - Warsaw University of Technology (PL)
Idaszek J. - inna afiliacja
Kołbuk D. - IPPT PAN
Choińska E. - Warsaw University of Technology (PL)
Chlanda A. - Warsaw University of Technology (PL)
Święszkowski W. - IPPT PAN
140p.
2.  Nasajpour A., Mostafavi A., Chlanda A., Rinoldi C., Sharifi S., Ji M.S., Ye M., Jonas S.J., Święszkowski W., Weiss P.S., Khademhosseini A., Tamayol A., Cholesteryl ester liquid crystal nanofibers for tissue engineering applications, ACS Materials Letters, ISSN: 2639-4979, DOI: 10.1021/acsmaterialslett.0c00224, Vol.2, No.9, pp.1067-1073, 2020

Streszczenie:
Liquid-crystal-based biomaterials provide promising platforms for the development of dynamic and responsive interfaces for tissue engineering. Cholesteryl ester liquid crystals (CLCs) are particularly well suited for these applications, due to their roles in cellular homeostasis and their intrinsic ability to organize into supramolecular helicoidal structures on the mesoscale. Here, we developed a nonwoven CLC electrospun scaffold by dispersing three cholesteryl ester-based mesogens within polycaprolactone (PCL). We tuned the ratio of our mesogens so that the CLC would be in the mesophase at the cell culture incubator temperature of 37°C. In these scaffolds, the PCL polymer provided an elastic bulk matrix while the homogeneously dispersed CLC established a viscoelastic fluidlike interface. Atomic force microscopy revealed that the 50% (w/v) cholesteryl ester liquid crystal scaffold (CLC-S) exhibited a mesophase with topographic striations typical of liquid crystals. Additionally, the CLC-S favorable wettability and ultrasoft fiber mechanics enhanced cellular attachment and proliferation. Increasing the CLC concentration within the composites enhanced myoblast adhesion strength promoted myofibril formationin vitrowith mouse myoblast cell lines.

Afiliacje autorów:
Nasajpour A. - Massachusetts Institute of Technology (US)
Mostafavi A. - inna afiliacja
Chlanda A. - Warsaw University of Technology (PL)
Rinoldi C. - inna afiliacja
Sharifi S. - inna afiliacja
Ji M.S. - inna afiliacja
Ye M. - inna afiliacja
Jonas S.J. - inna afiliacja
Święszkowski W. - inna afiliacja
Weiss P.S. - inna afiliacja
Khademhosseini A. - Massachusetts Institute of Technology (US)
Tamayol A. - Massachusetts Institute of Technology (US)
20p.
3.  Chlanda A., Oberbek P., Heljak M., Górecka Ż., Czarnecka K., Chen K.-S., Woźniak M.J., Nanohydroxyapatite adhesion to low temperature plasma modified surface of 3D-printed bone tissue engineering scaffolds - qualitative and quantitative study, SURFACE AND COATINGS TECHNOLOGY, ISSN: 0257-8972, DOI: 10.1016/j.surfcoat.2019.07.070, Vol.375, pp.637-644, 2019

Streszczenie:
Biodegradable 3D-printed polycaprolactone scaffolds for bone tissue engineering applications have been extensively studied as they can provide an attractive porous architecture mimicking natural bone, with tunable physical and mechanical properties enhancing positive cellular response. The main drawbacks of polycaprolactone-based scaffolds, limiting their applications in tissue engineering are: their hydrophobic nature, low bioactivity and poor mechanical properties compared to native bone tissue. To overcome these issues, the surface of scaffolds is usually modified and covered with a ceramic layer. However, a detailed description of the adhesion forces of ceramic particles to the polymer surface of the scaffolds is still lacking. Our present work is focused on obtaining PCL-based composite scaffolds to strengthen the architecture of the final product. In this manuscript, we report qualitative and quantitative evaluation of low temperature plasma modification followed by detailed studies of the adhesion forces between chemically attached ceramic layer and the surface of polycaprolactone-nanohydroxyapatite composite 3D-printed scaffolds. The results suggest modification-dependent alteration of the internal structure and morphology, as well as mechanical and physical scaffold properties recorded with atomic force microscopy. Moreover, changes in the material surface were followed by enhanced adhesion forces binding the ceramic layer to polymer-based scaffolds.

Słowa kluczowe:
surface modification, low temperature plasma, atomic force microscopy, bone tissue engineering

Afiliacje autorów:
Chlanda A. - Warsaw University of Technology (PL)
Oberbek P. - Warsaw University of Technology (PL)
Heljak M. - Warsaw University of Technology (PL)
Górecka Ż. - Warsaw University of Technology (PL)
Czarnecka K. - IPPT PAN
Chen K.-S. - Tatung University (TW)
Woźniak M.J. - Warsaw University of Technology (PL)
100p.
4.  Woźniak M., Chlanda A., Oberbek P., Heljak M., Czarnecka K., Janeta M., John Ł., Binary bioactive glass composite scaffolds for bone tissue engineering — structure and mechanical properties in micro and nano scale. A preliminary study, Micron, ISSN: 0968-4328, DOI: 10.1016/j.micron.2018.12.006, Vol.119, pp.64-71, 2019

Streszczenie:
Composite scaffolds of bioactive glass (SiO2-CaO) and bioresorbable polyesters: poly-L-lactic acid (PLLA) and polycaprolactone (PCL) were produced by polymer coating of porous foams. Their structure and mechanical properties were investigated in micro and nanoscale, by the means of scanning electron microscopy, PeakForce Quantitative Nanomechanical Property Mapping (PF-QNM) atomic force microscopy, micro-computed tomography and contact angle measurements. This is one of the first studies in which the nanomechanical properties (elastic modulus, adhesion) were measured and mapped simultaneously with topography imaging (PF-QNM AFM) for bioactive glass and bioactive glass – polymer coated scaffolds. Our findings show that polymer coated scaffolds had higher average roughness and lower stiffness in comparison to pure bioactive glass scaffolds. Such coating-dependent scaffold properties may promote different cells-scaffold interaction.

Słowa kluczowe:
bone tissue engineering, composite scaffold, bioactive glass, mmechanical properties

Afiliacje autorów:
Woźniak M. - Warsaw University of Technology (PL)
Chlanda A. - Warsaw University of Technology (PL)
Oberbek P. - Warsaw University of Technology (PL)
Heljak M. - Warsaw University of Technology (PL)
Czarnecka K. - IPPT PAN
Janeta M. - University of Wrocław (PL)
John Ł. - University of Wrocław (PL)
100p.
5.  Heljak M.K., Moczulska-Heljak M., Choińska E., Chlanda A., Kosik-Kozioł A., Jaroszewicz T., Jaroszewicz J., Święszkowski W., Micro and nanoscale characterization of poly(DL-lactic-co-glycolic acid) films subjected to the L929 cells and the cyclic mechanical load, Micron, ISSN: 0968-4328, DOI: 10.1016/j.micron.2018.09.004, Vol.115, pp.64-72, 2018

Streszczenie:
In this paper, the effect of the presence of L929 fibroblast cells and a cyclic load application on the kinetics of the degradation of amorphous PLGA films was examined. Complex micro and nano morphological, mechanical and physico-chemical studies were performed to assess the degradation of the tested material. For this purpose, molecular weight, glass transition temperature, specimen morphology (SEM, μCT) and topography (AFM) as well as the stiffness of the material were measured. The study showed that the presence of living cells along with a mechanical load accelerates the PLGA degradation in comparison to the degradation occurring in acellular media: PBS and DMEM. The drop in molecular weight observed was accompanied by a distinct increase in the tensile modulus and surface roughness, especially in the case of the film degradation in the presence of cells. The suspected cause of the rise in stiffness during the degradation of PLGA films is a reduction in the molecular mobility of the distinctive superficial layer resulting from severe structural changes caused by the surface degradation. In conclusion, all the micro and nanoscale properties of amorphous PLGA considered in the study are sensitive to the presence of L929 cells, as well as to a cyclic load applied during the degradation process.

Słowa kluczowe:
L929, aliphatic polyester, stiffness rise

Afiliacje autorów:
Heljak M.K. - Warsaw University of Technology (PL)
Moczulska-Heljak M. - IPPT PAN
Choińska E. - Warsaw University of Technology (PL)
Chlanda A. - Warsaw University of Technology (PL)
Kosik-Kozioł A. - Warsaw University of Technology (PL)
Jaroszewicz T. - Warsaw University of Technology (PL)
Jaroszewicz J. - inna afiliacja
Święszkowski W. - IPPT PAN
30p.
6.  Chlanda A., Kijeńska E., Rinoldi C., Tarnowski M., Wierzchoń T., Święszkowski W., Structure and physico-mechanical properties of low temperature plasma treated electrospun nanofibrous scaffolds examined with atomic force microscopy, Micron, ISSN: 0968-4328, DOI: 10.1016/j.micron.2018.01.012, Vol.107, pp.79-84, 2018

Streszczenie:
Electrospun nanofibrous scaffolds are willingly used in tissue engineering applications due to their tunable mechanical, chemical and physical properties. Additionally, their complex openworked architecture is similar to the native extracellular matrix of living tissue. After implantation such scaffolds should provide sufficient mechanical support for cells. Moreover, it is of crucial importance to ensure sterility and hydrophilicity of the scaffold. For this purpose, a low temperature surface plasma treatment can be applied. In this paper, we report physico-mechanical evaluation of stiffness and adhesive properties of electrospun mats after their exposition to low temperature plasma. Complex morphological and mechanical studies performed with an atomic force microscope were followed by scanning electron microscope imaging and a wettability assessment. The results suggest that plasma treatment can be a useful method for the modification of the surface of polymeric scaffolds in a desirable manner. Plasma treatment improves wettability of the polymeric mats without changing their morphology.

Słowa kluczowe:
Atomic force microscopy, Surface modification, Electrospun fibers, RF plasma treatment, Tissue engineering, Nanomaterial

Afiliacje autorów:
Chlanda A. - Warsaw University of Technology (PL)
Kijeńska E. - Warsaw University of Technology (PL)
Rinoldi C. - inna afiliacja
Tarnowski M. - Warsaw University of Technology (PL)
Wierzchoń T. - Warsaw University of Technology (PL)
Święszkowski W. - inna afiliacja
30p.
7.  Rinoldi C., Kijeńska E., Chlanda A., Choińska E., Khenoussi N., Tamayol A., Khademhosseini A., Święszkowski W., Nanobead-on-string composites for tendon tissue engineering, JOURNAL OF MATERIALS CHEMISTRY B , ISSN: 2050-7518, DOI: 10.1039/c8tb00246k, Vol.6, No.19, pp.3116-3127, 2018

Streszczenie:
Tissue engineering holds great potential in the production of functional substitutes to restore, maintain or improve the functionality in defective or lost tissues. So far, a great variety of techniques and approaches for fabrication of scaffolds have been developed and evaluated, allowing researchers to tailor precisely the morphological, chemical and mechanical features of the final constructs. Electrospinning of biocompatible and biodegradable polymers is a popular method for producing homogeneous nanofibrous structures, which might reproduce the nanosized organization of the tendons. Moreover, composite scaffolds obtained by incorporating nanoparticles within electrospun fibers have been lately explored in order to enhance the properties and the functionalities of the pristine polymeric constructs. The present study is focused on the design and fabrication of biocompatible electrospun nanocomposite fibrous scaffolds for tendon regeneration. A mixture of poly(amide 6) and poly(caprolactone) is electrospun to generate constructs with mechanical properties comparable to that of native tendons. To improve the biological activity of the constructs and modify their topography, wettability, stiffness and degradation rate, we incorporated silica particles into the electrospun substrates. The use of nanosize silica particles enables us to form bead-on-fiber topography, allowing the better exposure of ceramic particles to better profit their beneficial characteristics. In vitro biocompatibility studies using L929 fibroblasts demonstrated that the presence of 20 wt% of silica nanoparticles in the engineered scaffolds enhanced cell spreading and proliferation as well as extracellular matrix deposition. The results reveal that the electrospun nanocomposite scaffold represents an interesting candidate for tendon tissue engineering.

Afiliacje autorów:
Rinoldi C. - inna afiliacja
Kijeńska E. - Warsaw University of Technology (PL)
Chlanda A. - Warsaw University of Technology (PL)
Choińska E. - Warsaw University of Technology (PL)
Khenoussi N. - Université de Haute Alsace (FR)
Tamayol A. - Massachusetts Institute of Technology (US)
Khademhosseini A. - Massachusetts Institute of Technology (US)
Święszkowski W. - inna afiliacja
8.  Witecka A., Yamamoto A., Idaszek J., Chlanda A., Święszkowski W., Influence of biodegradable polymer coatings on corrosion, cytocompatibility and cell functionality of Mg-2.0Zn-0.98Mn magnesium alloy, COLLOIDS AND SURFACES B-BIOINTERFACES, ISSN: 0927-7765, DOI: 10.1016/j.colsurfb.2016.04.021, Vol.144, pp.284-292, 2016

Streszczenie:
Four kinds of biodegradable polymers were employed to prepare bioresorbable coatings on Mg-2.0Zn-0.98Mn (ZM21) alloy to understand the relationship between polymer characteristics, protective effects on substrate corrosion, cytocompatibility and cell functionality. Poly-l-lactide (PLLA), poly(3-hydroxybutyrate) (PHB), poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) or poly(lactic-co-glycolic) acid (PLGA) was spin-coated on ZM21, obtaining a smooth, non-porous coating less than 0.5 μm in thickness. Polymer coating characterization, a degradation study, and biocompatibility evaluations were performed. After 4 w of immersion into cell culture medium, degradation of PLGA and PLLA coatings were confirmed by ATR-FTIR observation. The coatings of PLLA, PHB and PHBV, which have lower water permeability and slower degradation than PLGA, provide better suppression of initial ZM21 degradation and faster promotion of human osteosarcoma cell growth and differentiation.

Słowa kluczowe:
Biodegradable metal, Magnesium alloy, Biodegradable polymer, SaOS-2 differentiation, Calcification

Afiliacje autorów:
Witecka A. - inna afiliacja
Yamamoto A. - National Institute for Materials Science (JP)
Idaszek J. - inna afiliacja
Chlanda A. - Warsaw University of Technology (PL)
Święszkowski W. - inna afiliacja
35p.

Kategoria A Plus

IPPT PAN

logo ippt            ul. Pawińskiego 5B, 02-106 Warszawa
  +48 22 826 12 81 (centrala)
  +48 22 826 98 15
 

Znajdź nas

mapka
© Instytut Podstawowych Problemów Techniki Polskiej Akademii Nauk 2021