Partnerzy

Streszczenie:
This study investigates the effect of build orientation on the fatigue performance of Haynes 282 alloy manufactured via Direct Metal Laser Sintering at 0°, 45°, and 90°. Fatigue tests revealed superior service life for 0° and 45° orientations, attributed to equiaxed grains and high-angle grain boundaries identified by EBSD. Vertical builds exhibited columnar grains and reduced fatigue resistance. This work provides the first systematic correlation between grain boundary character and low-cycle fatigue behavior in DMLS-manufactured Haynes 282, expanding current understanding beyond Inconel-based systems and offering insights for orientation-based design optimization in critical high-temperature applications

Słowa kluczowe:
Nickel alloys, Fatigue, Additive manufacturing, Direct metal laser sintering (DMLS)

Streszczenie:
This study explores the influence of printing orientation on the yield surface characteristics and their evolution under plastic pre-deformation in additively manufactured (AM) stainless steel 316L produced via laser powder bed fusion (LPBF). Tubular specimens were fabricated in three orientations (XY, ZX, and Z) and subjected to multi-axial loading to experimentally determine initial and subsequent yield surfaces using a single-specimen probing approach. The yield surfaces were derived at two offset strain definitions (0.001% and 0.005%) and further analyzed after tensile pre-deformations of 0.35%, 0.5%, and 0.8%. Results revealed strong anisotropy in the AM specimens, with the Z-oriented samples displaying the lowest yield strength and most significant softening. In contrast, the XY and ZX orientations exhibited higher resistance to plastic deformation. The wrought SS316L showed superior mechanical performance. The evolution of yield surfaces highlighted the orientation-dependent hardening/softening mechanisms and directional stress redistribution. Electron backscatter diffraction (EBSD) analysis revealed that the microstructural anisotropy and grain morphology—particularly the presence of columnar grains in the Z-oriented samples—correlate strongly with the observed mechanical anisotropy and yield surface asymmetry

Słowa kluczowe:
Stainless steel, Yield surface, Additive manufacturing, Laser powder bed fusion melting (LPBF-M)

Streszczenie:
In this study, Haynes 282 alloy bars were fabricated using Direct Metal Laser Sintering (DMLS) in three build orientations: 0°, 45°, and 90°. The process was conducted under an argon protective atmosphere with an energy density of 104 J/mm³, a laser power of 100 W, and a scanning speed of 800 mm/s. The additively manufactured (AM) specimens underwent fatigue testing at stress amplitudes ranging from ±550 MPa to ±800 MPa. Specimens printed at 0° and 45° showed significantly improved mechanical performance, indicating these orientations are more favorable. Notably, the AM specimens demonstrated extended service life at stress amplitudes below 700 MPa, highlighting the potential of DMLS for producing durable Haynes 282 components.

Słowa kluczowe:
Haynes 282,nickel alloys,fatigue,additive manufacturing,Direct Metal Laser Sintering (DMLS)

Streszczenie:
This study investigates the influence of build orientation on the microstructure and early-stage deformation behaviour of austenitic stainless steel 316 L (SS316L) produced via laser powder bed fusion (LPBF). Three LPBF specimen orientations: horizontal (XY), inclined at 45° (ZX), and vertical (Z) were compared to conventionally produced wrought SS316L. Mechanical testing was conducted under uniaxial tension to fracture and to a controlled axial strain of 1 % to capture the onset of plasticity. Electron backscatter diffraction (EBSD) was performed before and after deformation to quantify grain boundary character, misorientation distribution, and grain morphology evolution. The LPBF material exhibited notable differences in yield strength and strain hardening, with the Z-oriented specimens exhibiting the lowest mechanical performance due to insufficient interlayer bonding and elongated melt pool boundaries aligned with the build direction. In contrast, the XY and ZX orientations showed relatively higher strength and more uniform deformation behaviour. EBSD revealed that early-stage plastic deformation led to the intragranular misorientation accumulation but the degree of it varied significantly with orientation. Wrought SS316L displayed the highest overall mechanical properties and more homogeneous deformation due to its equiaxed, recrystallized microstructure.

Słowa kluczowe:
Stainless steel, Microstructure, Additive manufacturing, Laser Powder Bed Fusion Melting (LPBF-M)