Instytut Podstawowych Problemów Techniki
Polskiej Akademii Nauk

Partnerzy

V.M. Zubko


Ostatnie publikacje
1.  Tarelnyk V., Haponova O., Melnyk V., Tarelnyk N., Zubko V., Vlasovets V., Konopliachenko V., Bondarev S., Radionov O., Mayfat M., Okhrimenko V., Tkachenko A., The Surfaces Properties of Steel Parts with Wear-Resistant Coatings of the 1M and 90% BK6 + 10% 1M Composition Applied by the Method of Electrospark Alloying with the Use of Special Technological Environments. Pt. 1. The Strengthened-Surfaces’ Structural State Features, Metallofizika i Noveishie Tekhnologii, ISSN: 1024-1809, DOI: 10.15407/mfint.45.05.0663, Vol.45, No.5, pp.663-686, 2023

Streszczenie:
The article describes a new method of forming the protective coatings of steel parts operating under conditions of abrasive wear both in general mechanical engineering, the composition of which is of 90% ВК6 + 10% 1М, and in industries, where there may be radiation exposure and the composition of 1М (70% Ni, 20% Cr, 5% Si, 5% B), by applying them by the method of electrospark alloying (ESA) with compact electrodes-tools made of nichrome wire X20Н80 and ВК6 hard alloy and using special technological media (STM), which include the necessary alloying elements. As a result of these research, it is established that the surface layers of the 45 and Р6M5 steels after applying wear-resistant coatings have a structure that consists of three areas: the ‘white layer’, the transition zone below, and the base metal. When the discharge energy (Wp) increases from 0.52 to 2.6 J, the thicknesses of the ‘white layer’ and the transition zone, their microhardness and surface roughness increase, but the integrity of the applied coating decreases. The highest microhardness of 9750-12800 and 14250-14600 MPa corresponds to the coating formed on steel 45 and Р6M5, respectively, during ESA by means of both the compact electrodes-tools made of hard alloy ВК6 and the STM with the composition of 0.5% Si + 0.5% B + 2% Cr + 7% Ni + 90% Vaseline.

Słowa kluczowe:
electrospark alloying, electrode tool, coating, white layer, microhardness, roughness, continuity

Afiliacje autorów:
Tarelnyk V. - inna afiliacja
Haponova O. - inna afiliacja
Melnyk V. - inna afiliacja
Tarelnyk N. - inna afiliacja
Zubko V. - inna afiliacja
Vlasovets V. - inna afiliacja
Konopliachenko V. - inna afiliacja
Bondarev S. - inna afiliacja
Radionov O. - inna afiliacja
Mayfat M. - inna afiliacja
Okhrimenko V. - inna afiliacja
Tkachenko A. - inna afiliacja
40p.
2.  Tarelnyk V., Haponova O., Konoplianchenko V., Tarelnyk N., Mikulina M., Gerasimenko V., Vasylenko O., Zubko V., Melnyk V., Properties of Surfaces Parts from X10CrNiTi18-10 Steel Operating in Conditions of Radiation Exposure Retailored by Electrospark Alloying. Pt. 3. X-ray Spectral Analysis of Retailored Coatings, Metallofizika i Noveishie Tekhnologii, ISSN: 1024-1809, DOI: 10.15407/mfint.44.10.1323, Vol.44, No.10, pp.1323-1333, 2022

Streszczenie:
In article we present the results of studies of the local x-ray spectral analysis of coatings formed by the electrospark alloying (ESA) method at the discharge energy Wp = 0.13, 0.52 and 0.9 J by anodes from nickel and stainless steel X10CrNiTi18-10 on the cathode surface from X10CrNiTi18-10 steel. During ESA by stainless steel X10CrNiTi18-10 anode with an increase Wp in characteristic points and from the entire investigated surface of the coating, the quantitative elemental composition is not changed. The analysis of elements distribution over the depth of the formed layer is showed that when using the electrode tool from steel X10CrNiTi18-10 with an increase in Wp, there are a slight decrease in chromium and an increase in nickel and titanium in the surface layer. When steel X10CrNiTi18-10 is replaced by nickel with an increase in Wp, the concentration of nickel on the coating surface decreases from 95.38 to 89.04%. As the recession deepens from the coating surface, the concentration of nickel gradually decreases, respectively, at Wp = 0.13, 0.52 and 0.9 J from 96.29, 90.29 and 89.04% on the surface to 9.0, 10.30 and 9.9% at depth: 120, 165 and 240 μm. At the same time, the concentration of chromium, titanium and iron gradually increases.

Słowa kluczowe:
electrospark alloying, nickel, steel, x-ray spectral analysis, scan step, topography, spectrum

Afiliacje autorów:
Tarelnyk V. - Sumy National Agrarian University (UA)
Haponova O. - IPPT PAN
Konoplianchenko V. - inna afiliacja
Tarelnyk N. - Sumy National Agrarian University (UA)
Mikulina M. - inna afiliacja
Gerasimenko V. - inna afiliacja
Vasylenko O. - inna afiliacja
Zubko V. - inna afiliacja
Melnyk V. - inna afiliacja
40p.

Kategoria A Plus

IPPT PAN

logo ippt            ul. Pawińskiego 5B, 02-106 Warszawa
  +48 22 826 12 81 (centrala)
  +48 22 826 98 15
 

Znajdź nas

mapka
© Instytut Podstawowych Problemów Techniki Polskiej Akademii Nauk 2024